CONNECTIONS
CAUTION
Connections should always be made with power OFF!
Ethernet Connection
Connect the Ethernet cradle (Ethernet port 1) to an Ethernet hub or a port on
the host device. Connect the Ethernet cradle (power port) to power supply.
Figure 3 - Ethernet Connection
Key:
A)
Datalogic Jet™ Ethernet Multi Cradle
B)
94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
C)
UTP CAT 5E cable (recommended use)
D) Ethernet
hub
Daisychaining Ethernet Connection
To connect several cradles to an Ethernet network, Ethernet cradles may be
daisychained. It is recommended not to connect more than 4 cradles in order
to maintain the optimal baud rate. The Speed LED and the Link LED on the
Ethernet Port 2 function in the same way as the Speed LED and the Link LED
on the front of the cradle.
To daisychain cradles:
1. Connect the first Ethernet cradle to power and to the Ethernet Switch as
shown on Figure 4.
2. Connect power to the second Ethernet cradle.
3. Connect the daisychain Ethernet cable (either straight or twisted cable
can be used) between Ethernet Port 2 of the first cradle, and Ethernet
Port 1 of the second cradle.
4. Connect additional cradles as shown in Figure 4.
Figure 4 - Daisychaining Ethernet Connection
Key:
A) Ethernet
hub
B)
Ethernet Port 1
C)
Ethernet Port 2
D)
94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
E)
UTP CAT 5E cable (recommended use).
Power Supply
Each Ethernet Multi Cradle requires a power supply to be connected to
the cradle. We recommend the DL FPS18 power supply.
GND
VEXT
Figure 5 - Power Supply Polarity
Datalogic Mobile S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara
Bologna - Italy
07
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DL JET Ethernet Desk Multi Cradle
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive
e
92/31/EEC, 93/68/EEC
emendamenti successivi
and
further amendments
et
ses successifs amendements
und
späteren Abänderungen
y
succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla
sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product
safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité
des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit
und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad
electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022 (C
LASS
A ITE), A
UGUST
1994
:
A
MENDMENT
A1 (C
LASS
A ITE), O
CTOBER
2000
:
L
IMITS AND METHODS OF MEASUREMENTS OF RADIO
DISTURBANCE OF INFORMATION TECHNOLOGY EQUIPMENT
EN 55024, S
EPTEMBER
1998
:
I
NFORMATION
T
ECHNOLOGY
E
QUIPMENT
. I
MMUNITY
CHARACTERISTICS
. L
IMITS AND METHODS OF
MEASUREMENTS
Lippo di Calderara, August 22nd, 2007
Paola Chientaroli
Quality Assurance Manager
D
A
B
C
D
C
B
A
E