*RO = read only, WO = write only, R/W = read/write
Device Specific Parameters
Index
(dec)
Parameter
Object Name
Lenght
Subindex
(offset)
Value/Range
Description
Data Type
Access* Remark
0x0048 (72)
Delay Settings
1 octet
1(8)
0 = no DELAY (default
U03, T53, B53
)
0x1 = Delay ON/OFF
0x2 = Delay ON
0x4 = Delay OFF (default
W03
)
Select Delay mode (OFF)
UIntegerT
R/W
Saved in non-volatile memory.
Max. Value 255 ms
1 octet
2(0)
0...(2^8)-1
20 (default)
Delay value = Delay [ms]
UIntegerT
R/W
0x00B4 (180)
Output type
1 octet
1 octet
1(8)
2(0)
0x01 = PNP (default)
0x02 = NPN
0x03 = Push Pull
0x01 = PNP (default)
0x02 = NPN
0x03 = Push Pull
0x04 = Input
Output type of C/Q pin when in SIO mode
Output type of DO pin
UIntegerT
UIntegerT
R/W
R/W
Saved in non-volatile memory
0x0058 (88)
Keylock
1 octet
0x0 = All enabled (default)
0x1 = Push Button disabled
0x2 = Trimmer disabled
0x3 = All disabled
Keylock
UInterT
R/W
Saved in non-volatile memory
Standard Command
Index (dec) Command Name
Lenght Value (dec) Description
Access*
0x0002 (2)
SP1 Single Value Teach
1 octet
0x41 (65)
Reflector Acquisition (
B53, T53
) / EASY Acquisition (
U03
)
WO
0x0002 (2)
SP1 Teach TP1
1 octet
0x43 (67)
Acquisition FINE: Mark Detection (
W03, U03
) (refer to User’s Manual)
WO
0x0002 (2)
SP1 Teach TP2
1 octet
0x44 (68)
Acquisition FINE: Background Detection (
W03, U03
) (refer to User’s Manual)
WO
0x0002 (2)
Teach Dynamic /
Max. Sensitivity
1 octet
0x4B (75)
Dynamic acquisition (
W03
) / Max. Sensitivity (
T53, B53, U03
)
WO
0x0002 (2)
Teach Dynamic End
1 octet
0x4F (79)
Exit from Dynamic Detection (
W03
)
WO
0x0002 (2)
Restore Factory Settings
1 octet
0x82 (130)
Restore factory settings (Device Access Locks, Application Specific Tag, Function Tag, Location Tag, SSC1 Param, SSC1 Config, SSC2 Param, SSC1 Config,
Delay Settings, Sensitivity selection, Output type, RGB selection (
W03
), Frequency Selection (
U03
), Switch counter settings, Switch counter values, Keylock)
WO
0x0002 (2)
Confirm Maintenance
1 octet
0xA5 (165)
Reset Maintenance parameters (Operating Hours Maintenance, Minimum device temperature since powerup, Maximum device temperature since powerup,
Device Status, Detailed Device Status)
WO
0x0002 (2)
Disable/enable emission
1 octet
0xB0 (176)
Toggle emission (enable / disable emission)
WO
0x0002 (2)
Start / Stop Ping
1 octet
0xAF (175)
Feature to identify the sensor by yellow LED blinking
WO
Events
Event code (dec)
Event name
Event mode
Event type
Device status
Remarks
0x4220 (16928)
Temperature underrun
Appears / Disappears
Warning
Out of specification
0x4210 (16912)
Temperature overrun
Appears / Disappears
Warning
Out of specification
0x5100 (20736)
General power supply fault
Appears / Disappears
Error
Failure
0x7710 (30480)
Short circuit - Check installation
Appears / Disappears
Error
Failure
0x8C40 (35904)
Maintenance required - Lens cleaning
Appears / Disappears
Notification
Maintenance required
B53
only
0x8CA0 (36900)
Laser fault
Appears / Disappears
Error
Failure
B53
only
Summary of Contents for IO-Link S8
Page 10: ...821007030 Rev A...
