Datacom Systems SS-1200-S Series User Manual Download Page 26

Page: 26 / 37

SS-1200, SS-2200, SS-4200 Series USERguide

4.4.11

Set Upgrade (SE UP)

Usage

Guidelines

This command is used to allow the SINGLEstream to be upgraded. If turned off,
upgrade attempts will fail.

Syntax

Set Upgrade (on/off)

Example

Set Upgrade on

4.4.12

Show Device Uptime (SH DE UP)

Usage

Guidelines

This command is used to show how long the SINGLEstream has been powered.

Syntax

Show Device Uptime

Example

Show Device Uptime

4.4.13

Show Product (SH PR)

Usage

Guidelines

This command is used to show the model number, serial number, and software
version on the unit.

Syntax

Show Product

Example

Show Product

4.4.14

Show TCP CONNECTIONS (SH TC CO)

Usage

Guidelines

This command is used to show any current connections to the SINGLEstream.

Syntax

Show TCP Connections

Example

Show TCP Connections

4.4.15

Show (SH)

Usage

Guidelines

This command is used to show the current time, date, IP settings, model number,
serial number, and software version on the unit.

Syntax

Show

Example

Show

4.4.16

Show Time (SH TI)

Usage

Guidelines

This command is used to show the current time.

Syntax

Show Time

Example

Show Time

Summary of Contents for SS-1200-S Series






































Search results

Summary of Contents for SS-1200-S Series

Reviews:

Related manuals for SS-1200-S Series

Brands by name

Popular brands

Datacom Systems SS-1200-S Series, User Manual

Search results

Summary of Contents for SS-1200-S Series

Reviews:

Related manuals for SS-1200-S Series

Brands by name

Popular brands