Datacom Systems SS-1200-S Series User Manual Download Page 22 | Manualshive

Page: 22 / 37

background image

© 2017 Datacom Systems Inc

22

SS-1200, SS-2200, SS-4200 Series USERguide

4.3.5

What happens after the relays close? – Auto Mode

Auto Reconnect Mode Flow Diagram

Auto mode:

When the relays close as a result of LINKprotect® activating, the Tap will wait a user-
programmed period of time before attempting to reactivate the network ports. Once a failover
occurs in this mode, the monitoring tools connected to the SINGLEstream will not receive
traffic until link has been re-established on the network ports.

This mode allows the SINGLEstream to keep checking to see if link status has been recovered.
If it detects that the link has been recovered, it will place the network pair back into normal
operation mode and send traffic to the monitoring ports. Both Tap ports may go up/down to
check the link status.

«
...
20
21
22
23
24
...
»

Summary of Contents for SS-1200-S Series






































Reviews:

No comments

Related manuals for SS-1200-S Series

Brand: CAME Pages: 4

System x3630 M4

Brand: IBM Pages: 7

Brand: Ubiquiti Pages: 3

Brand: Watchguard Pages: 39

Brand: AMD Pages: 20

Brand: Renesas Pages: 941

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

18x18 Card Cage

Brand: WolfPack Pages: 31

Brand: H3C Pages: 4

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: Toto Link Pages: 57

Brand: Aerotech Pages: 62

Brand: Lanner Pages: 43

Brand: Datavideo Pages: 71

Brand: ASTRO Pages: 12

Brand: Transition Networks Pages: 5

Brand: Supero Pages: 18

EK-FC 780 GTX Lightning

Brand: ekwb Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands