Datacolor 110 User Manual Download Page 11 | Manualshive

Page: 11 / 40

background image

USB Driver Installation

Installing the Driver

To connect to a USB port, additional software must be installed.

1. Install the CD labeled

USB Drivers and Documentation

into the CD ROM drive.

2. Connect the USB cable to the instrument, and to the USB port on the computer. When

this connection is made, the system detects a new piece of hardware, and the screen
below automatically displays:

The New Hardware Wizard automatically replaces this screen.

3. Click

Next

to continue with the USB driver installation.

Datacolor 110 User's Guide

USB Driver Installation

•

7

«
...
9
10
11
12
13
...
»

Summary of Contents for 110









































Reviews:

No comments

Related manuals for 110

Brand: Oemtools Pages: 4

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Cambro Pages: 6

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: UniPix Pages: 24

Brand: Yamaha Pages: 48

Brand: KAM Pages: 5

Brand: Yacht Devices Pages: 32

Brand: Coba Pages: 2

Brand: Maselec Pages: 6

Brand: Otto Bock Pages: 52

Brand: Torin BIG RED Pages: 43

Brand: Blizzard Lighting Pages: 24

Brand: Sima Pages: 22

Pivot track filler

Brand: Norwest Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands