manualshive.com logo in svg

Data Translation DT9840 Series, User Manual

Share
Download
Data Translation DT9840 Series User Manual Download Page 51

Register Description

51

Calibration and Setup

The Calibration and Setup register, described in 

Table 6

, is located at address 0xB0000004. 

Address 0xB0000001 is the control register for the Xicor potentiometers, bias return resistors, 
and Scalable Bus termination resistors. The register select is CE3, described in 

Table 15 on 

page 70

, and requires a clock divider of four (40 ns).

Table 6: Calibration and Setup Register (Address 0xB0000004)

 

Bit

Register Description

a

Type

0 to 13

Reserved

R

14

When 1, sets the module for IEPE operation; streaming writes to DIO port 
2 are disabled. 

When 0, sets the module for normal operation; streaming writes to DIO 
port 2 are enabled.

R/W

15

For the DT9841, DT9841E, and DT9841-VIB when 1, sets the DAC 
voltage range to ±2.5 V; when 0, sets the DAC voltage range to ±10 V.

For the DT9842/2 and DT9842/8, this bit is reserved. The DAC voltage 
range is always ±10 V.

R/W

16

When 1, enables writing to the digital ports under DMA mode; when 0, 
disables writing to the digital ports under DMA mode.

R/W

17

When 1, the USB cable is connected; when 0, the USB cable is not 
connected.

R

18

DSP heartbeat signal readable by the USB interface without having to go 
through the host port interface. This bit is toggled by the DSP program to 
indicate the program is running.

R/W

19

Data input bit for the Xicor potentiometer (see also bit 31).

R

20

When 1, enables the chip that controls the A/D 1 k

Ω 

termination resistors 

(see bits 26 and 27). When 0, disables the chip that controls the A/D 
termination resistors.

R/W

21

For the DT9841, DT9841E, and DT9841-VIB, data from the D/A (MDO 
line). For the DT9842/2 and DT9842/8, this bit is reserved.

R/W

22

For the DT9841, DT9841E, and DT9841-VIB, data to the D/A (MDI line).
For the DT9842/2 and DT9842/8, this bit is reserved.

R/W

23

For the DT9841, DT9841E, and DT9841-VIB, clock for the D/A (MC line).
For the DT9842/2 and DT9842/8, this bit is reserved.

R/W

24

For the DT9841, DT9841E, and DT9841-VIB, select for the D/A (ML line).
For the DT9842/2 and DT9842/8, this bit is reserved.

R/W

25

When 1, enables the Scalable Bus 100 

Ω 

termination resistors; write to 

address 0xB000000C. When 0, disables the Scalable Bus 100 

Ω 

termination resistors. 

R/W

26

b

Data bit for the chip that controls the 1 k

Ω 

termination resistors on the A/D 

inputs (see bits 20 and 27). 

R/W

Summary of Contents for DT9840 Series



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands