manualshive.com logo in svg

Data Link CW232, Manual

Share
Download
Data Link CW232 Manual Download Page 6

Connection Example 

 

Please connect it according to the following procedures.   

1) CW232/422 is connected between two equipment that monitor it as shown in the figure below.   

2) To display the monitor data, CW232/422 is connected between WindowsPC with the USB cable.   

3) On WindowsPC, the CW232/422 application program is started.   

4) It is confirmed to recognize CW232/422 by the CW232/422 application program's normally 

starting.  

5) It is assumed the state that can be communicated by turning on the power supply of the device at 

monitored both ends.   

6) The CW232/422 application program is set, and it is assumed the state of the monitor beginning.   

7) The communication that wants to be actually monitored between devices at both ends begins. 

   

Attention:  

※

  Please connect both sides in correct way. 

※

  Please note the signal polarity of    sufficiently when you connect CW422 main body to the 

communication line.   

※

  There is a possibility that it causes the breakdown like the damage of the equipment etc. when the 

polarity of    is connected by mistake.   

 

 

 

Summary of Contents for CW232













Reviews:

No comments

Brands by name

Popular brands

Load more brands