Data Link CW232 Manual Download Page 1

Simple User's Manual

   

Ver1.1

         

2006.3    DATA LINK Co., Ltd 

CW232

·

CW232/V

·

CW422

Compact Watch RS232C/RS422 Analyzer

 

 

Introduction

 

Thank you for your choosing our RS232C/RS422 Analyzer 

CW232(V)/CW422

.  

This manual will give you some notices about how to use this product. 

Please read the content before you use the product. 

Please agree to omit (V) of CW232/V in the following sentences, and to unite it only to the mark 

named 

CW232/CW422

 

Package Contents

 

 

Simple manual (this book) 

 

Install CD-ROM 

 

CW232/CW422 main body 

 

USB cable

 

 

Please contact our Sales Department though it descends to the packing of the product with 

scrupulous care if any of the above items of the package is missing. 

System Requirement

 

Correspondence OS: Windows98SE / 2000 / XP  

Recommended environment:   

CPU _______Intel Pentium / Celelon 800MHz or above 

RAM ______256 MB or above 

HDD_______300 MB free space or above 

USB _______USB1.1 or above 

Others______External Graphic Card instead of the built-in one is recommended. 

When the application program is installed, the CD-ROM driver is necessary. 

Notification 

 

Memory and hard disk capacity necessary for operating the program might be different depending on 

the system environment used. 

 

It should be tested in the above-mentioned, recommended environment, otherwise it probably      

exists some instance that operation cannot be completely guaranteed according to customer's 

environment. 

 

Various specifications of the product are subjected to variation without a previous notice. Please    

acknowledge it beforehand. 

 

Please not connect it to interfaces other than USB and RS232C/RS422.

It cause damage and fire, etc.

 

 

Please not put it on moisture, dust, lamp soot or damp.       

         It causes fire etc. 

 

Please not use or leave it in the place of the high temperature  like  the  place  where  direct        

sunshine in close contact with the heater strikes.                  

It causes fire etc.

 

 

Please not put the foreign body internally to remodel it.       

 

    It causes fire, the electric shock, and the injury.

 

 

 

Please not touch by a wet hand.

                                                              It causes the electric shock. 

 

Please remove all cables at once and not go on using when generation of heat is felt or abnormality 

such as smelling to strangeness is confirmed by any chance. Please contact the shop of purchase.

 

Summary of Contents for CW232













Reviews: