background image

Q u i c k   I n s t a l l a t i o n   G u i d e  

H B 5 1   H y b r i d   i n v e r t e r

 

R e v . 1  

© 2 0 1 8   D a r f o n   E l e c t r o n i c s   C o r p .  

4

  |   P a g e  

CONNECTIONS 

 

System Types: Quick Disconnect Terminals 

 

Installing Conductors in to the Terminal Blocks

1.

 

Push a screwdriver into terminal.

 

2.

 

Insert the wire into the terminal.

 

3.

 

Remove the screwdriver.

 

 

Installing the Battery Conductors 

1.

 

Crimp or bolt ring lugs to the battery 
cables. 

 

2.

 

Connect the red cable to the 
positive (+) battery terminal. 

 

3.

 

Connect the black cable to the 
negative (-) battery terminal. 

 

 

8mm

(0.3in)

16mm

(0.6in)

Ring Lug Dimensions

Torque Value:
2 to 3Nm
(18 to 26 in-lb)

Torque  Value:
2 to 3Nm
(18 to 26 in-lb)

Wire/Cable Requirements 

 

GRID 

LOAD  BATTERY 

Size

 

8 AWG 

8 AWG 

2 AWG 

Length

 

-- 

-- 

< 3m 

 
Strip 15mm(0.6in) off the AC wires and 
battery cables. 

 

WARNINGS 

Make sure the circuit breaker is off before making or modifying any connections. 

To prevent the risk of electric shock, make sure the ground wire is properly earthed 
before operating this unit whether the grid is connected or not. 

To reduce the risk of injury, use the recommended wire/cable size. 

Do not apply anti-oxidant substance on battery terminals connections are made. 

Notes 

Order of connections should be Grid, Load, then Battery. 

Order of wire connections should be Ground, N, L1, L2. 

Connect AC wires according to the labels on the terminal block or your system type. 

Summary of Contents for HB51









Reviews: