EN
Table 1a.
Supported produced created by DARCO
Device steered
PK1
-
PK2
-
LR
[1]
LG
[1]
LT
[1]
n
min
[rev/min.]
n
max
[rev/min.]
base position
0
0
f
-
-
-
-
TH150-T
0
4
1
1
1
90
500
TH150
0
5
1
1
2
90
300
TH200
0
6
1
1
3
90
270
THP200
0
7
1
2
1
90
380
THP250
0
8
1
2
2
90
380
THP300
0
9
1
2
3
90
280
THP350
1
0
1
2
4
90
262
TH400
1
1
1
3
1
40
180
TH500
1
2
1
3
2
40
180
ANeco1-II
4
5
2
2
1
610
1500
ANeco2-II
4
6
2
2
2
610
1500
ANeco3-II
4
7
2
2
3
610
1500
GCKV150
5
5
3
2
1
1000
2250
GCKV200
5
6
3
2
2
1000
2300
Table 1b.
Additional controller functions
Function
PK1
-
PK2
-
LR
[1]
LG
[1]
LT
[1]
U
min
[V]
U
max
[V]
regulated voltage source 5V
9
8
0
0
0
0
5
regulated voltage source 10V
9
9
0
0
0
0
10
where:
PK1, PK2 - selected number on coding switch
LR
- number of LED diode flashes green (describing family of devices)
LG
- number of LED diode flashes red (describing group of devices)
LT
- number of LED diode flashes orange (describing type of device)
n
min
- minimal rotation speed
n
max
- maksymalmaximal rotation speed
U
min
- minimal voltage R at the R output
U
max
- maximum voltage R at the R output
SIGNALING
Table 2.
Starting procedure (with confirmation of type of device selected):
Signaling
Description
LED light flashes green.
Signaling the family of device steered (see table 1/column LR).
LED light flashes red.
Signaling the group of device steered (see table 1/column LG).
LED light flashes yellow.
Signaling the type of device steered (see table 1/column LT).
Table 3.
Operating statuses of connected and correctly functioning controller:
Signaling
Description
LED light lights green.
Actual rotation speed of steered device varies from the one set on controller no more than 40% of value set.
LED light flashes green.
Actual rotation speed of steered device varies from the one set on controller in the range of 40% to 80% of value set.
LED light is o
ff
.
Controller is in standby mode (knob is turned completely le
ft
).
SIGNALING OF EMERGENCY SITUATIONS
Table 4.
Singaling of incorrect values of PK1 and PK2 code switches (fig.1 pos.10):
Symptom of malfunction
Cause
LED light flashes green.
Coding switches have not been positioned to steer any device (base position 00).
LED light flashes yellow.
Coding switches have been positioned to steer a device that is not supported.
LED light flashes red.
Internal damage of controller.
Table 5.
Signalling of incorrect levels of voltage supplied:
Symptom of malfunction
Cause
LED light flashes:
3 x red,
1 x yellow
Too high voltage connected to the controller.
LED light flashes:
2 x red,
1 x yellow.
Too low voltage connected to the controller.
LED light flashes:
1 x red,
1 x yellow.
Internal damage of controller.
Table 6.
Others:
Symptom of malfunction
Cause
LED light is o
ff
in spite of
setting rotation speed.
1. Incorrect supplied voltage polarity.
2. S+ cable damaged.
3. S- cable damaged.
4. Controller power feeder damaged.
5. Internal damage of controller.
LED light lights red, but motor
of steered device does not
rotate.
1. R cable damaged.
2.Steered device has been blocked mechanically.
3. Internal damage of controller.
LED light lights red, but motor
of steered device turns on for
30 seconds and then switches
o
ff
for 60 seconds.
1. I cable damaged.
2. Internal damage of controller.
MAINTENANCE
No maintenance required.
Summary of Contents for ERO-32MN-1
Page 7: ......
