background image

 3

• 

Always operate the unit with the AC ground wire connected to the electrical system ground.  

• 

Connecting amplifier outputs to oscilloscopes or other test equipment, while the amplifier is in 
bridged mode, may damage both the amplifier and test equipment. 

• 

Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output. 

• 

Please turn off the power switch, when changing the power cord or signal cable, or select the input 
mode switch. 

• 

In typical use, Please set the volume to 0dB position. 

• 

Sometimes, when you want to send one signal to more than one amplifier, you should use a signal 
distributor. 

• 

For replacement use fuses of same type and rating only. 

• 

Prevent distortion! Make sure that all components connected to the Vision have sufficient power 
ratings. Otherwise distortion will be generated because the components are operated at their limits. 

• 

Avoid ground loops! Always be sure to connect the power amps and the mixing console to the same  
electrical circuit to ensure the same phase! 

• 

If system is dropped or struck, disconnect mains power supply immediately. Have a qualified 
engineer inspect for safety before operating. 

• 

If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not 
switch it on immediately. The arising condensation water might damage your system. Leave the 
system switched off until it has reached room temperature. 

• 

Repairs, servicing and electric connection must be carried out by a qualified technician. 

• 

WARRANTY: Till one year after date of purchase. 

 

OPERATING DETERMINATIONS 

 
If this system is operated in any other way, than the one described in this manual, the product may suffer 
damages and the

 

warranty becomes void.  

Any other operation may lead to dangers like short-circuit, burns, electric shock, etc. 
 
You endanger your own safety and the safety of others! 
 

Improper installation can cause serious damage to people and property !

 

 
 
 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

• 

In system setup, the amplifier's output power must be 50%-100% more than the loaded 
loudspeakers rated power. 

Summary of Contents for Vision 1600

















Reviews: