DAPAudio Platinum Manual Download Page 4

2

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

SAFETY INSTRUCTIONS

Every person involved with the installation, operation and maintenance of this system has to:

-

 be 

qualified

-

 

follow  the instructions of this manual

Before you initial start-up, please make sure that there is no damage caused by transportation. Should there
be any, consult your dealer and do not use the system.

To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow
the safety instructions and warning notes written in this manual.

Please consider that damages caused by manual modifications to the system are not subject to warranty.

This system contains no user-serviceable parts. Refer servicing to qualified technicians only.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the system.

  Never let the power-cord come into contact with other cables! Handle the power-cord and all

connections with the mains with particular caution!

  Never remove warning or informative labels from the unit.

  Never use anything to cover the ground contact.

  Never leave any cables lying around.

  Do not insert objects into air vents.

  Do not connect this system to a dimmerpack.

  Do not switch the system on and off in short intervals, as this would reduce the system’s life.

  Do not open the device and do not modify the device.

  Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output.

  Do not plug Mics into the console (or stagebox) while Phantom Power is on. Also mute the monitor /

Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of
seconds, before setting the input gains.

  Only use system indoor, avoid contact with water or other liquids.

  Avoid flames and do not put close to flammable liquids or gases.

  Always disconnect power from the mains, when system is not used. Only handle the power-cord by

the plug. Never pull out the plug by tugging the power-cord.

  Always operate the unit with the AC ground wire connected to the electrical system ground.

CAUTION!

Keep this system away from rain and moisture!

CAUTION! Be careful with your operations.

With a dangerous voltage you can suffer

a dangerous electric shock when touching the wires!

Summary of Contents for Platinum


















Reviews: