background image

 

12 

Before switching off the power 

 

When you have finished using the CD player, before switching off the power, be sure that the disc holder 
has been closed with the OPEN/CLOSE button. 
 
CAUTION: Do not forcibly close the disc holder when the power is off. 
 

CD’s  
1.

 Precautions on handling compact discs 

• Do not allow fingerprints, oil or dust to get on the surface of the disc. If the disc is dirty, wipe it off with a  
   soft dry cloth. 
• Do not use benzene, thinner, water, record spray, electrostatic-proof chemicals, or silicone-treated  
   cloths to clean discs. 
• Always handle discs carefully to prevent damaging the surface; in particular when removing a disc  
   from its case or returning it. 
• Do not bend the disc. 
• Do not put the CD near heating sources. 
• Do not enlarge the hole in the center of the disc. 
• Do not write on the label (printed side) with a hard-tipped implement such as a pencil or ball point pen. 
• Condensation will form if a disc is brought into a warm area from a colder one, such as outdoors in  
   winter. Do not attempt to dry the disc with a hair dryer, etc. 
 

2.

 

Precaution on storage

 

• After playing a disc, always unload it from the player. 
• Always store the disc in the jewel case to protect from dirt or damage. 
• Do not place discs in the following areas: 
1. Areas exposed to face sunlight for a considerable time. 
2. Areas subject to accumulation of dust or high humidity. 
3. Areas are affected by heat from indoor heaters, etc.

 

 
 

Connecting Outputs. 

Speakers are connected using terminal connectors. See the examples below and following page. 

 

Low impedance outputs 

You can use as many speakers as you want as long as the total impedance matches the amplifiers 
output. 

 

Example 1: 

using the 4

Ω

 output with two 8

Ω

 speakers.

 

 

 

 

 

 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

     

Fig. 5 

Example 2: 

using the 4

Ω

 output with four 4

Ω

 speakers

 

 

 
 
 
 
 

 
 

 

 

 

 

 

 

 

 

 

 

                       Fig. 6 

 

 

Summary of Contents for PA90CDT V3



















Reviews: