background image

 

Maintenance

 

The DAP Audio IPS-AS requires almost no maintenance. However, you should keep the unit clean. 
Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in 
liquid. Do not use alcohol or solvents. 
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections 
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying 
electric power.

 

 

Replacing a Fuse 

Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the 
fuse burns out, the product will not function whatsoever. If this happens, 

follow the directions below to do 

so.

 

1.

 Unplug the unit from the electric power source. 

2.

 Insert a screwdriver into the slot in the fuse cover. Open the fuseholder. 

3.

 Remove the broken fuse. If brown or unclear, it is burned out. 

4.

 Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover.  

    Be sure to use a fuse of the same type and specification. See the product specification label for  
    details.

 

 
 

Troubleshooting 

DAP Audio IPS-AS 
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps 
below in sequence until a solution is found. Once the unit operates properly, do not carry out following 
steps. 

1.

 If the device does not operate properly, unplug the device. 

2.

 Check the fuse, power from the wall, all cables, etc. 

3.

 If all of the above appears to be O.K., plug the unit in again.

 

4.

 If you are unable to determine the cause of the problem, do not open the amplifier, as this may  

    Damage the unit and the warranty will become void. 

5. 

Return the amplifier to your Dap Audio dealer. 

 
 

Product Specifications 

 

 Model  

 M/S Amplifier Switcher 

 Power supply 

 AC 110~120V / 220~240V, 60Hz  / 50Hz 
 DC 24V 

 Power Consumption  

 <18W 

 Channel 

 4 Channels 

 Switching Capacity 

 20A /150V Audio Signal 

 Input Theshold 

 5mV, Constant 100ms 

 Output Threshold 

 50mV,constant 20ms  

 Checking Cycle 

 500ms  6 time 

 Input Sensitivity 

 0dBV 10k

Ω

 

 Dimensions  (W*H*D) 

 483*88*370mm 

 Weight 

 8.2kg 

 
 
Design and product specifications are subject to change without prior notice. 

 

 

 

 

         Website: 

www.DAP-audio.info

 

Email: 

[email protected]

 

Summary of Contents for IPS-AS













Reviews: