background image

 

  

 

 

11 

   

 

Core Beat 

D2313  

Connect a Bluetooth device 

 
1.  Turn on your Bluetooth device. 
2.  Power on the DAP Audio Core Beat. 
3.  Press the Pair/Unpair button on the DAP Audio Core Beat. 
4.  Navigate to your Bluetooth device‟s setup screen, find “BT CORE” and connect. 
 

Note: If your Bluetooth device prompts for a pairing code, enter „0000‟. 

5.  The DAP Audio Core Beat pairing LED will light up solid when it is 'paired'. 

Note: If your Bluetooth device is not able to pair to the mixer, press the Pair/Unpair button on the 
mixer to break previous Bluetooth connections and reset the Bluetooth module. 

6.  To disconnect pairing, press the Pair/Unpair button on the DAP Audio Core Beat. 
7.  To connect to a different Bluetooth device, repeat steps 4-5. 
 

Maintenance 

 
The Dap Audio Core Beat requires almost no maintenance. However, you should keep the unit clean. 
Disconnect the mains power supply and then wipe the cover with a damp cloth. Do not immerse in 
liquid. Do not use alcohol or solvents. 
Keep connections clean. Disconnect electric power and then wipe the connections with a damp cloth. 
Make sure connections are thoroughly dry before linking equipment or supplying electric power. 
 

Troubleshooting 

 
DAP Audio Core Beat 
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps 
below in sequence until a solution is found. Once the unit operates properly, do not carry out following 
steps. 
1.  If the device does not operate properly, unplug the device. 
2.  Check power from the wall, all cables, connections, etc. 
3.  If all of the above appears to be O.K., plug the unit in again. 
4.  If nothing happens after 30 seconds, unplug the device. 
5.  Return the device to your DAP Audio dealer. 
 
 

 

Summary of Contents for Core Beat

















Reviews: