background image

Technical and Safety Notices

Important Safety Instructions

1.

  Read these instructions.

2.

  Keep these instructions.

3.

  Heed all warnings.

4.

  Follow all instructions.

5.

  Do not use this apparatus near water.

6.

  Do not submerge the equipment in water or liquids. 

7.

    Do not use any aerosol spray, cleaner, disinfectant or 

fumigant on, near or into the equipment. 

8.

  Clean only with a dry cloth.

9.

    Do not block any ventilation opening. Install in accordance 

with the manufacturer’s instructions.

10.

   Do not install near any heat sources such as radiators, heat 

registers, stoves, or other apparatus (including amplifiers) 
that produce heat.

11.

   To reduce the risk of electrical shock, the power cord shall 

be connected to a mains socket outlet with a protective 
earthing connection.

12.

   Do not defeat the safety purpose of the polarized or 

grounding type plug. A polarized plug has two blades with 
one wider than the other. A grounding type plug has two 
blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.

13.

   Protect the power cord from being walked on or pinched 

particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.

14.

   Do not unplug the unit by pulling on the cord, use the plug.

15.

   Only use attachments/accessories specified by the 

manufacturer.

16.

   Unplug this apparatus during lightning storms or when 

unused for long periods of time.

17.

   Refer all servicing to qualified service personnel. Servicing 

is required when the apparatus has been damaged in any 
way, such as power supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.

18.

   The appliance coupler, or the AC Mains plug, is the AC 

mains disconnect device and shall remain readily accessible 
after installation. 

19.

  Adhere to all applicable, local codes.

20.

   Consult a licensed, professional engineer when any 

doubt or questions arise regarding a physical equipment 

installation.

Environmental Statement

This product complies with international 
directives, including but not limited to the 
Restriction of Hazardous Substances (RoHS) 
in electrical and electronic equipment, the 
Registration, Evaluation, Authorization and 
restriction of Chemicals (REACH) and the 

disposal of Waste Electrical and Electronic Equipment (WEEE). 
Consult your local waste disposal authority for guidance on 
how properly to recycle or dispose of this product.

Summary of Contents for DSA125X4























Reviews: