Daniels Electronics Ltd. VT-3AM Instruction Manual Download Page 8

DE

DANIELS

ELECTRONICS

1-4

VT-3A130 VHF AM Transmitter Instruction Manual

1 . 3 . 2

 

Audio Specifications

Audio Input:

-25 to 0 dBm into a 600

 balanced load

Audio Response:

Flat audio; +1/-3 dB: 300 Hz - 3 kHz

Audio Distortion:

Less than 3% -40˚C to +60˚C at 30% modulation

Less than 5% -40˚C to +60˚C at 90% modulation

1 . 3 . 3

 

Physical Specifications

Physical Dimensions:

Width:

Height:

Depth:

7.1 cm (2.8 in)

12.8 cm (5.05 in)

19 cm (7.5 in)

Module Weight:

1.4 kg (3.0 lb.)

Corrosion Prevention:

Anodized aluminum construction. Stainless steel  hardware.
Selectively conformal coated glass epoxy 2 and 4 layer
printed circuitboards. Gold plated module connectors.

Module Design:

Compact  Eurostandard modular design. Plug-in modules
mate with Daniels standard M3 repeater subrack. Subracks /
modules comply with IEEE 1101, DIN 41494 and IEC 297-
3 (mechanical size / modular arrangement).

External Connections:

RF Connection: type N connector located on the transmitter

module front panel.  Motherboard Connections (Audio,
Power, and Control) are made through a 48 pin, gold plated,
type F connector on the rear of the transmitter module. User
connection made through mated "mother board" assembly of
the repeater subrack.  Type F  standard connector complies
with DIN 41612 Level 2 (200 mating cycles, 4 day 10 ppm
SO

2

 gas test with no functional impairment and no change in

contact resistance).

Summary of Contents for VT-3AM

















Reviews: