background image

51

51

Danfoss District Energy 

VI.GP.P1.02 

DKDHR

Instructions 

 

 

 

VX Solo II

14.0  Troubleshooting

If operating disturbances occur, the following basic features 

should be checked before carrying out actual troubleshooting:

-  the substation is connected to electricity,

-  the strainer on the district heating supply is clean,

-  the district heating flow temperature is at normal level 

      (summer at least 60 °C, winter at least 70 °C),

-  the differential pressure is higher than or equal to the normal

  (local) differential pressure in the district heating network. -  

  If in doubt, ask the district heating plant,

-  there is pressure on the system.

 

14.1 Troubleshooting - Heating

Problem

Possible cause

Solution

No heat

Strainer clogged on DH og HE side 

(radiator circuit).

Clean strainer.

Filter in district heating meter clogged.

Clean the filter (after consulting the 

district heating plant).

Defective differential pressure controller.

Check the functions of the differential 

pressure controller - clean valve seat if 

required.

Defective sensor

Replace sensor

Defektive actuator.

Check the functioning of the actuator.

Defective motor valve - or possibly dirt 

in the valve housing.

Check the functions of the motor valve - 

clean valve housing if required.

Automatic controls wrongly set or defec-

tive - possibly power failure.

Check if the setting of the controller is 

correct - see separate instructions. Check 

the power supply.

Temporary setting of actuator to “man-

ual” control - see instruction on heating 

circuit, manual control.

Pump out of operation.

Check that the pump is receiving power 

and that it runs. Control that there is 

no air in the pump housing - see pump 

manual.

The pump is set at too low speed of 

rotation.

Set the pump at higher speed of rotation 

- see instructions on heating circuit.

Air pockets in the system.

Vent the installation thoroughly.

Uneven heat distribution

Air pockets in the system.

Vent the installation thoroughly.

Supply temperature too high

Wrong setting of automatic controls.

Adjust automatic controls, see instruc-

tions for automatic controls.

Defective sensor.

Replace sensor.

Defective controller. The controller does 

not react as it is should in accordance 

with the instructions.

Call in automatic controls manufacturer 

or replace controller.

Summary of Contents for VX Solo II

























































Reviews: