0-65 Personal Menu Password
Range:
Function:
200
*
[0 - 999 ] Define the password for access to the My
Personal Menu via the [Quick Menu] key. If
0-66 Access to Personal Menu w/o Password
is set
to
Full access
[0], this parameter will be ignored.
0-66 Access to Personal Menu w/o Password
Option:
Function:
[0]
*
Full access Disables password defined in
[1]
Read only Prevents unauthorized editing of My Personal
Menu parameters.
[2]
No access Prevents unauthorized viewing and editing of My
Personal Menu parameters.
If
0-61 Access to Main Menu w/o Password
is set to
Full access
[0], this parameter will be ignored.
3.2.8 0-7* Clock Settings
Set the time and date of the internal clock. The internal clock
can be used for e.g. Timed Actions, energy log, Trend
Analysis, date/time stamps on alarms, Logged data and
Preventive Maintenance.
It is possible to program the clock for Daylight Saving Time /
summertime, weekly working days/non-working days
including 20 exceptions (holidays etc.). Although the clock
settings can be set via the LCP, they can also be set along
with timed actions and preventative maintenance functions
using the MCT 10 software tool.
NOTE
The frequency converter has no back up of the clock
function and the set date/time will reset to default
(2000-01-01 00:00) after a power down unless a Real Time
Clock module with back up is installed. If no module with
back up is installed, it is recommended the clock function is
only used if the frequency converter is integrated into the
BMS using serial communications, with the BMS maintaining
synchronization of control equipment clock times. In
it is possible to program for a Warning in
case clock has not been set properly, e.g. after a power
down.
NOTE
If mounting an Analog I/O MCB 109 option card, a battery
back-up of the date and time is included.
0-70 Date and Time
Range:
Function:
Size related
*
[0 - 0 ]
0-71 Date Format
Option:
Function:
Sets the date format to be used in the LCP.
[0]
*
YYYY-MM-DD
[1]
*
DD-MM-YYYY
[2]
MM/DD/YYYY
0-72 Time Format
Option:
Function:
Sets the time format to be used in the LCP.
[0]
*
24 h
[1]
12 h
0-74 DST/Summertime
Option:
Function:
Choose how Daylight Saving Time/Summertime
should be handled. For manual DST/Summertime
enter the start date and end date in
and
[0]
*
Off
[2]
Manual
0-76 DST/Summertime Start
Range:
Function:
Size related
*
[0 - 0 ]
0-77 DST/Summertime End
Range:
Function:
Size related
*
[0 - 0 ]
0-79 Clock Fault
Option:
Function:
Enables or disables the clock warning, when the
clock has not been set or has been reset due to a
power-down and no backup is installed. If MCB 109
is installed “enabled” is default
[0]
*
Disabled
[1]
Enabled
0-81 Working Days
Array with 7 elements [0] - [6] displayed below parameter number
in display. Press OK and step between elements by means of
▲
and
▼
buttons on the LCP.
Option: Function:
Set for each weekday if it is a working day or a non-
working day. First element of the array is Monday. The
working days are used for Timed Actions.
[0]
*
No
[1]
Yes
Parameter Description
VLT
®
HVAC Drive Programming Guide
36
MG.11.CB.02 - VLT
®
is a registered Danfoss trademark
3
3
