5 Typecode and Selection
5.1 Drive Configurator for VLT
®
Integrated Servo Drive ISD 510
The Danfoss Drive Configurator (
) is an advanced but easy-to-use tool to configure the Danfoss VLT
®
Integrated Servo Drive ISD 510 that exactly matches your requirements.
NOTICE
The Drive Configurator shows the valid configuration of servo drive variants. Only valid combinations are shown.
Therefore, not all variants detailed in the type code (see
chapter 5.2.1 Typecode and Definitions
) are visible.
The Drive Configurator generates a unique code number for the servo drive required, preventing errors during order entry.
Decoding is also available: Enter a typecode and the Drive Configurator decodes the configuration and show the configu-
ration of the servo drive.
5.2 VLT
®
Integrated Servo Drive ISD 510
5.2.1 Typecode and Definitions
Pos.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Fixed
I S D 5 1 0 T
D 6
Variant
A 0 1 C 5
E 5 4 F R X P L S X X T F 0 7 6 S X N 4 6 X S X S X
S 0 2 C 1
E 6 7 F S 1 E C S C O F F 0 8 4 C 0 N 4 0 B K S C X
0 2 C 9
F M 1 P N
F 1 0 8
N 2 9 C
0 3 C 8
E N
F 1 3 8
N 2 4
Table 5.1 Type Code
[01–03] Product group
[21–22]
Bus system
[33–35]
Motor speed
ISD
VLT
®
Integrated Servo Drive
PL
Ethernet POWERLINK
®
N46
Rated speed 4600 RPM
[04–06] Product variant
EC
EtherCAT
®
N40
Rated speed 4000 RPM
510
ISD
®
510
PN
PROFINET
®
1)
N29
Rated speed 2900 RPM
[07]
Hardware configuration
EN
EtherNet/IP
™
1)
N24
Rated speed 2400 RPM
A
Advanced
[23–25]
Firmware
[36]
Mechanical brake
S
Standard
SXX
Standard
X
Without brake
[08]
Drive torque
SC0
Customized version
B
With brake
T
Torque
[26]
Safety
[37]
Motor shaft
[09–12] Torque
T
Safe Torque Off (STO)
S
Standard smooth shaft
01C5
1.5 Nm
F
Functional safety
1)
K
Standard fitted key
1)
02C1
2.1 Nm
[27–30]
Flange size
C
Customized
02C9
2.9 Nm
F076
76 mm
[38]
Motor sealing
03C8
3.8 Nm
F084
84 mm
X
Without sealing
[13–14] DC voltage
F108
108 mm
1)
S
With sealing
D6
600 V DC-link voltage
F138
138 mm
1)
[39–40]
Surface coating
[15–17] Drive enclosure
[31–32]
Flange type
SX
Standard
E54
IP54
SX
Standard
CX
Customized
E67
IP67 (shaft IP65)
C0
Customized version
[18–20] Drive feedback
FRX
Resolver
FS1
Single-turn feedback
FM1
Multi-turn feedback
Table 5.2 Legend to Typecode
1) In preparation
Typecode and Selection
VLT
®
Integrated Servo Drive ISD
®
510 System
50
Danfoss A/S © 08/2017 All rights reserved.
MG36C102
5
5
