Danfoss VLT AutomationDrive User Manual Download

Page: 1 / 59

VLT

AutomationDrive EtherNet/IP

MG.90.Jx.02 ver. 5

September 2007 – VLT is a registered Danfoss trademark

Contents

Safety Note.......................................................................................................................... 3

Introduction ..........................................................................................................................3

About this Manual................................................................................................................. 3

Technical Overview ............................................................................................................... 3

Assumptions ........................................................................................................................ 3

Hardware ............................................................................................................................ 3

Background Knowledge ......................................................................................................... 3

FC 300-related Literature....................................................................................................... 3

ODVA Conformance .............................................................................................................. 3

Abbreviations ....................................................................................................................... 3

How to Install .......................................................................................................................3

The EtherNet/IP Option .........................................................................................................3

LED Behaviour ..................................................................................................................... 3

Topology ............................................................................................................................. 3

Network .............................................................................................................................. 3

Recommended Design Rules .................................................................................................. 3

EMC Precautions................................................................................................................... 3

How to Install Option in Frequency Converter........................................................................... 3

How to Configure the System ................................................................................................3

IP Settings........................................................................................................................... 3

Ethernet Link Parameters ...................................................................................................... 3

Configuring the Scanner ........................................................................................................3

IP traffic .............................................................................................................................. 3

How to Control the FC 300 ....................................................................................................3

I/O Assembly Instances.........................................................................................................3

EtherNet/IP connections ........................................................................................................3

Control Word Profile.............................................................................................................. 3

Change of State, COS ...........................................................................................................3

Danfoss FC Control Profile...................................................................................................... 3

ODVA Control Profile ............................................................................................................. 3

Reference Handling............................................................................................................... 3

Parameters............................................................................................................................3

Parameter List...................................................................................................................... 3

Data Types Supported by FC 300............................................................................................ 3

Troubleshooting ....................................................................................................................3

Alarm Word and Warning Word .............................................................................................. 3

Appendix ...............................................................................................................................3

Supported CIP Objects ..........................................................................................................3

Index ....................................................................................................................................3

Summary of Contents for VLT AutomationDrive




























































Search results

Summary of Contents for VLT AutomationDrive

Reviews:

Related manuals for VLT AutomationDrive

Brands by name

Popular brands

Danfoss VLT AutomationDrive, Manual

Search results

Summary of Contents for VLT AutomationDrive

Reviews:

Related manuals for VLT AutomationDrive

Brands by name

Popular brands