13-02 Stop Event
Select the boolean (true or false) input to deactivate smart logic
control.
Option:
Function:
[39]
Start
command
[40]
Drive stopped
[41]
Reset Trip
[42]
Auto-reset Trip
[43]
Ok key
[OK] is pressed. Only available on
the graphical LCP.
[44]
Reset key
[Reset] is pressed. Only available on
the graphical LCP.
[45]
Left key
[
◄
] is pressed. Only available on the
graphical LCP.
[46]
Right key
[
►
] is pressed. Only available on the
graphical LCP.
[47]
Up key
[
▲
] is pressed. Only available on the
graphical LCP.
[48]
Down key
[
▼
] is pressed. Only available on the
graphical LCP.
[50]
Comparator 4
[51]
Comparator 5
[60]
Logic rule 4
[61]
Logic rule 5
[70]
SL Time-out 3 Smart logic controller timer 3 is
timed out.
[71]
SL Time-out 4 Smart logic controller timer 4 is
timed out.
[72]
SL Time-out 5 Smart logic controller timer 5 is
timed out.
[73]
SL Time-out 6 Smart logic controller timer 6 is
timed out.
[74]
SL Time-out 7 Smart logic controller timer 7 is
timed out.
[75]
Start
command
given
[76]
Digital input
x30/2
[77]
Digital input
x30/3
[78]
Digital input
x30/4
[83]
Broken Belt
[102]
Relay 1
[103]
Relay 2
13-03 Reset SLC
Option:
Function:
[0]
*
Do not reset
SLC
Retain programmed settings in
parameter group 13-** Smart Logic
.
[1]
Reset SLC
Reset all parameters in
parameter
group 13-** Smart Logic
to default
settings.
4.12.2 13-1* Comparators
Comparators are used for comparing continuous variables
(that is output frequency, output current, analog input, and
so on) to fixed preset values.
Par. 13-11
Comparator Operator
=
TRUE longer than.
. . .
. . .
Par. 13-10
Comparator Operand
Par. 13-12
Comparator Value
130BB672.10
Illustration 4.38 Comparators
There are digital values that are compared to fixed time
values. See the explanation in
parameter 13-10 Comparator
Operand
. Comparators are evaluated once in each scan
interval. Use the result (true or false) directly. All
parameters in this parameter group are array parameters
with index 0–5. Select index 0 to program comparator 0,
select index 1 to program comparator 1, and so on.
13-10 Comparator Operand
Option:
Function:
Options
[1] Reference %
to
[31]
Counter B
are variables which are
compared based on their values.
Options
[50] FALSE
to
[186] Drive in
auto mode
are digital values (true/
false) where the comparison is
based on the amount of time
during which they are set to true or
false. See
parameter 13-11 Comparator
Operator
Select the variable to be monitored
by the comparator.
[0]
DISABLED
The comparator is disabled.
[1]
Reference %
The resulting remote reference in
percent.
[2]
Feedback %
[RPM] or [Hz], as set in
parameter 0-02 Motor Speed Unit
.
Parameter Descriptions
Programming Guide
MG06J202
Danfoss A/S © 03/2019 All rights reserved.
119
4
4
Summary of Contents for VLT AutomationDrive FC 361
Page 2: ......
