Danfoss VLT AutomationDrive FC 360, Application Manual, Page: 11 / 31

•
Input the tension reference in parameter
parameter 37-21 Tension Set Point .
•
Set parameter parameter 37-57 Tension On/Off to
[1] On , parameter parameter 37-59 Diameter Reset
to [0] Off , and then initiate a start signal.
Parameter Value
3-03 Maximum Reference 50
3-41 Ramp 1 Ramp Up Time 0.05
3-42 Ramp 1 Ramp Down Time 0.05
5-30 Terminal 27 Digital Output [174] TLD indicator
5-31 Terminal 29 Digital Output [173] End of roll
5-70 Term 32/33 Pulses Per
Revolution Based on the winder encoder.
5-71 Term 32/33 Encoder
Direction Based on the winder encoder.
6-10 Terminal 53 Low Voltage 0
6-11 Terminal 53 High Voltage 10
6-14 Terminal 53 Low Ref./
Feedb. Value 0
6-15 Terminal 53 High Ref./
Feedb. Value 100
6-19 Terminal 53 mode [1] Voltage mode
6-70 Terminal 45 Mode [2] Digital Output
Parameter 6-72 Terminal 45
Digital Output [176] Ready to run
6-90 Terminal 42 Mode [0] 0–20 mA
6-91 Terminal 42 Analog
Output [162] Tapered tension set point
6-93 Terminal 42 Output Min
Scale 0
6-94 Terminal 42 Output Max
Scale 100
7-00 Speed PID Feedback
Source [1] 24V encoder
7-07 Speed PID Feedback Gear
Ratio Based on the application.
17-10 Signal Type Based on the line encoder.
17-11 Resolution (PPR) Based on the line encoder.
Parameter 37-00 Application
Mode [0] Drive mode
Parameter 37-20 Winder Mode
Selection [0] Wind
Parameter 37-22 Taper Set
Point 0
Parameter 37-23 Partial Roll
Diameter Value 5.000%
Parameter 37-24 Core1
Diameter Based on the application.
Parameter 37-25 Core2
Diameter Based on the application.
Parameter 37-26 Winder Jog
Speed 1
Parameter 37-27 TLD Low Limit
0
Parameter 37-28 TLD High Limit 90
Parameter 37-29 TLD Timer 1
Parameter 37-30 TLDOnDelay 1
Parameter 37-31 Diameter Limit
Detector 90
Parameter 37-32 Initial
Diameter Measurement [0] Set diameter when diameter
reset (default)
Parameter 37-33 Diameter
Measurement Input [0] No function
Parameter 37-34 Reading at
Core 0.00
Parameter 37-35 Reading at
Full Roll 0.00
Parameter 37-36 Tension Set
Point Input [0] Par.3721
Parameter 37-37 Taper Set
Point Input [0] Par.3722
Parameter 37-38 Tension
Feedback Input [1] Input 53(0–10 V DC or 0–20
mA )
Parameter 37-39 Tension
Feedback Type Based on the application.
Parameter 37-40 Center Winder
Cmd Src [1] Parameter 19-61–19-67
control the functions
Parameter 37-41 Diameter
Change Rate 0.02
Parameter 37-42 Tapered
Tension Change Rate 0.2
Parameter 37-43 Diameter
Calculator Min Speed 0.5
Parameter 37-44 Line
Acceleration Feed Forward 0
Parameter 37-45 Line Speed
Source [2] MCB102
Parameter 37-46 Winder Speed
Match Scale 1.000
Parameter 37-47 Tension PID
Profile Based on the application.
Parameter 37-48 Tension PID
Proportional Gain Based on the application.
Parameter 37-49 Tension PID
Derivate Time Based on the application.
Parameter 37-50 Tension PID
Integral Time Based on the application.
Parameter 37-51 Tension PID
Out Limit 0.00%
Parameter 37-52 Tension PID
Der Gain Limit Based on the application.
Parameter 37-53 Tension PID
Anti Windup [1] Enable
Parameter 37-54 Winder Jog
Reverse 0
Parameter 37-55 Winder Jog
Forward 0
Parameter 37-56 New Diameter
Select [0] Core Diameter
Center Winder Control
VLT
®
AutomationDrive FC 360
10 Danfoss A/S © 11/2014 All rights reserved. MG06E102
3 3