3.15 Parameters: 15-** Drive Information
3.15.1 15-0* Operating Data
15-00 Operating hours
Range:
Function:
0 h
*
[0 - 2147483647 h] View how many hours the frequency
converter has run. The value is saved
when the frequency converter is
turned off.
15-01 Running Hours
Range:
Function:
0 h
*
[0 -
2147483647 h]
View how many hours the motor has run.
Reset the counter in
parameter 15-07 Reset Running Hours
Counter
. The value is saved when the
frequency converter is turned off.
15-02 kWh Counter
Range:
Function:
0 kWh
*
[0 -
2147483647
kWh]
Register the power consumption of
the motor as an average value over 1
hour. Reset the counter in
parameter 15-06 Reset kWh Counter
.
15-03 Power Up's
Range:
Function:
0
*
[0 - 2147483647 ] View the number of times the frequency
converter has been powered up.
15-04 Over Temp's
Range:
Function:
0
*
[0 - 65535 ] View the number of frequency converter
temperature faults.
15-05 Over Volt's
Range:
Function:
0
*
[0 - 65535 ] View the number of frequency converter
overvoltages.
15-06 Reset kWh Counter
Option:
Function:
[0]
*
Do not reset
No reset of the kWh counter is required.
[1]
Reset counter Press [OK] to reset the kWh counter to 0
(see
).
15-07 Reset Running Hours Counter
Option:
Function:
[0]
*
Do not
reset
[1]
Reset
counter
To reset the running hours counter to 0, select
[1] Reset
and press [OK] (see
). This
15-07 Reset Running Hours Counter
Option:
Function:
parameter cannot be selected via the serial
port, RS485.
Select
[0] Do not reset
if no reset of the
running-hours counter is required.
3.15.2 15-1* Data Log Settings
The data log enables continuous logging of up to 4 data
sources (
parameter 15-10 Logging Source
) at individual rates
(
parameter 15-11 Logging Interval
). A trigger event
(
parameter 15-12 Trigger Event
) and window
(
parameter 15-14 Samples Before Trigger
) are used to start
and stop the logging conditionally.
15-10 Logging Source
Option:
Function:
Select which variables
are to be logged.
[0]
*
None
[15]
Readout: actual setup
[1397] Alert Alarm Word
[1398] Alert Warning Word
[1399] Alert Status Word
[1472] Legacy Alarm Word
[1473] Legacy Warning Word
[1474] Leg. Ext. Status Word
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference %
[1603] Status Word
[1606] Actual Position
[1607] Target Position
This option is only
available for software
version 48.XX
[1608] Position Error
This option is only
available for software
version 48.XX
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor current
[1616] Torque [Nm]
[1617] Speed [RPM]
[1618] Motor Thermal
[1620] Motor Angle
[1621] Torque [%] High Res.
[1622] Torque [%]
[1624] Calibrated Stator Resistance
[1625] Torque [Nm] High
Parameter Descriptions
VLT
®
AutomationDrive FC 301/302
202
Danfoss A/S © 10/2018 All rights reserved.
MG33MP02
3
3
Summary of Contents for VLT AutomationDrive FC 302
Page 2: ......
