Danfoss VLT Automation Drive FC 360, Programming Manual

Page: 43 / 156

3-04 Reference Function
Option: Function:
[0]
*
Sum Sums both external and preset reference
sources.
[1] External/
Preset Use either the preset or the external
reference source. Shift between external and
preset via a command or a digital input.
4.4.2 3-1* References
Select the preset reference(s). Select Preset ref. bit 0/1/2
[16], [17] or [18] for the corresponding digital inputs in
parameter group 5-1* Digital Inputs .
3-10 Preset Reference
Range: Function:
0 %
*
[-100 -
100 %] Enter up to 8 different preset references (0-7)
in this parameter, using array programming.
Select
preset reference bit 0/1/2 [16], [17], or [18]
for the corresponding digital inputs in
parameter group
5-1* Digital Inputs , for
selecting dedicated references.
3-11 Jog Speed [Hz]
Range: Function:
5 Hz
*
[ 0 - 400.0
Hz] The jog speed is a fixed output speed which
the frequency converter is running when the
jog function is activated. See also
parameter 3-80 Jog Ramp Time .
3-12 Catch up/slow Down Value
Range: Function:
0 %
*
[0 -
100 %] Enter a percentage (relative) value to be either
added to or deducted from the actual reference
for catching up or slowing down respectively. If
[28] Catch up is selected via one of the digital
inputs ( parameter 5-10 Terminal 18 Digital Input to
parameter 5-15 Terminal 33 Digital Input ), the
percentage (relative) value is added to the total
reference. If
[29] Slow down is selected via one of
the digital inputs ( parameter 5-10 Terminal 18
Digital Input to parameter 5-15 Terminal 33 Digital
Input ), the percentage (relative) value is deducted
from the total reference.
3-14 Preset Relative Reference
Range: Function:
0 %
*
[-100 -
100 %] The actual reference, X, is increased or decreased
with the percentage Y, set in
parameter 3-14 Preset Relative Reference . This
results in the actual reference Z. Actual reference
(X) is the sum of the inputs selected in
parameter 3-15 Reference 1 Source ,
parameter 3-16 Reference 2 Source ,
3-14 Preset Relative Reference
Range: Function:
parameter 3-17 Reference 3 Source , and
parameter 8-02 Control Source .
Relative
Z=X+X*Y/100
Resulting
actual
reference
Y
X
130BA059.12
Z
Illustration 4.4 Preset Relative Reference
X
100 % 0 -100
Z
Y
X+X*Y/100
P 3-14
130BA278.10
Illustration 4.5 Actual Reference
3-15 Reference 1 Source
Option: Function:
Select the reference input to be used
for the first reference signal.
Parameter 3-15 Reference 1 Source ,
parameter 3-16 Reference 2 Source , and
parameter 3-17 Reference 3 Source define
up to 3 different reference signals. The
sum of these reference signals defines
the actual reference.
[0] No function
[1]
*
Analog Input 53
[2] Analog Input 54
[7] Frequency input
29
[8] Frequency input
33
[11] Local bus
reference
[20] Digital pot.meter
[32] Bus PCD
3-16 Reference 2 Source
Option: Function:
Select the reference input to be used
for the first reference signal.
Parameter 3-15 Reference 1 Source ,
parameter 3-16 Reference 2 Source , and
parameter 3-17 Reference 3 Source define
up to 3 different reference signals. The
Parameter Descriptions Programming Guide
MG06C602 Danfoss A/S © 7/2015 All rights reserved. 41
4 4