background image

28

AB243586442172en-001401

System design recommendations

To obtain optimum efficiency of the complete 
refrigerant system, optimised R410A heat 
exchangers must be used. R410A refrigerant has 
good heat transfer properties: it is worthwhile 
designing specific heat exchangers to gain in size 
and efficiency.

An evaporator with optimised R410A distributor 
and circuit will give correct superheat at outlet 
and optimal use of the exchange surface. This is 
critical for plate evaporators that have generally a 
shorter circuit and a lower volume than shell and 
tubes and air cooled coils.

For all evaporator types a special care is required 
for superheat control leaving the evaporator and 
oil return.

A sub-cooler circuit in the condenser that creates 
high sub cooling will increase efficiency at high 
condensing pressure. In R410A systems the 
positive effect of sub cooling on system efficiency 
will be significantly larger than in R22/R407C 
systems.

Furthermore, for good operation of the 
expansion device and to maintain good 
efficiency in the evaporator it is important 
to have an appropriate sub cooling. Without 
adequate sub cooling, flash gas will be formed at 
the expansion device resulting in a high degree 
of vapour at the expansion device inlet leading to 
low efficiency.

Heat exchangers

Refrigerant charge limit

Danfoss SH compressors can tolerate liquid 
refrigerant up to a certain extent without major 
problems. However, excessive liquid refrigerant in 
the compressor is always unfavourable for service 
life. Besides, the installation cooling capacity may 
be reduced because of the evaporation taking 
place in the compressor and/or the suction line 
instead of the evaporator. System design must be 
such that the amount of liquid refrigerant in the 
compressor is limited. In this respect, follow the 
guidelines given in the section “Essential piping 
design recommendations” in priority.

Use the tables below to quickly evaluate the 
required compressor protection in relation with 
the system charge and the application.

When the condenser is mounted at a higher 
position than the compressor, a suitably sized 
“U”-shaped trap close to the compressor is 
necessary to prevent oil leaving the compressor 
from draining back to the discharge side of the 
compressor during off cycle. The upper loop also 
helps avoid condensed liquid refrigerant from 
draining back to the compressor when stopped.

Discharge lines

HP

LP

Condenser

3D  exibility

U Trap

Upper loop

Model

Refrigerant charge limit 

(kg)

SH090

5.9

SH105-120-140-161-184

7.9

SH180-240-295

13.5

SH380

14.5

SH485

17

Application Guidelines

Summary of Contents for SH485





















































Reviews: