background image

Installation

15 mm

HM 8 bolt

Lock washer

Flat washer

Steel mounting

sleeve

Rubber grommet

Nut

HEAVY

do not lift

manually

Each Danfoss PSH scroll compressor is equipped 
with two lift rings on the top shell. Always use 
both these rings when lifting the compressor. 
Use lifting equipment rated and certified for 
the weight of the compressor. A spreader 
bar rated for the weight of the compressor is 
highly recommended to ensure a better load 
distribution. The use of lifting hooks closed 
with a clasp and certified to lift the weight of 
the compressor is also highly recommended. 
Always respect the appropriate rules concerning 
lifting objects of the type and weight of these 
compressors. Maintain the compressor in an 
upright position during all handling manoeuvres 
(maximum of 15° from vertical).
Never use only one lifting lug to lift the 
compressor. The compressor is too heavy for the 
single lug to handle, and the risk is run that the 
lug could separate from the compressor with 
extensive damage and possible personal injury 
as a result.
Store the compressor between -35°C and 50°C, 
not exposed to rain, corrosive or flammable 
atmosphere.

When the compressor is mounted as part of 
an installation, never use the lift rings on the 
compressor to lift the installation. The risk is run 
that the lugs could separate from the compressor 
or that the compressor could separate from the 
base frame with extensive damage and possible 
personal injury as a result.
Never apply force to the terminal box with the 
intention of moving the compressor, as the 
force placed upon the terminal box can cause 
extensive damage to both the box and the 
components contained inside.

Compressor handling and 

storage

Maximum inclination from the vertical plane 
while operating must not exceed 3 degrees.

Compressors PSH019-039 come delivered with 
four rubber mounting grommets and metal 
sleeve liners that serve to isolate the compressor 
from base frame. These grommets must always 
be used to mount the compressor in a single 
application. The grommets must be compressed 
until contact between the flat washer and 
the steel mounting sleeve is established. The 
grommets attenuate to a great extent the 
transmission of compressor vibrations to the base 
frame.

The required bolt size for the PSH019-039 
compressors is HM8-40. This bolt must be 
tightened to a torque of 15Nm.

Compressor mounting

Currently PSH019-23-26-30-34-39 are only 
qualified with even tandem combination. The 
recommended tandem piping design is similar 
to even tandem of SH090-105-120-140-161-184. 
More details about PSH tandem configuration 
and installation guideline, please refer to SH 

parallel Application Guideline FRCC.PC.008.  
(Note: The model reference relationship between 
PSH and SH are: PSH019 refer to SH090, PSH023 
refer to SH105, PSH026 refer to SH120, PSH030 
refer to SH140, PSH034 refer to SH161, PSH039 
refer to SH184).

Parallel Installation

29

FRCC.PC.022.A4.02

Application Guidelines

Summary of Contents for PSH019













































Reviews: