background image

Installation Guide

Temperature controller for walk-in coolers

and freezers, Type 

AK-RC 204B 

and 

AK-RC 205C

© Danfoss | Climate Solutions | 2022.08

AN41473467835501-000102 | 1

080R9293

AN41473467835501-000102

Warnings

•  Using the unit without observing the manufacturer's instructions may alter the appliance's safety requirements. Only probes 

supplied by Danfoss should be used for the unit to operate correctly.

•  From -40 – +20 °C, if the NTC probe is extended to 1000 m with at least 0.5 mm

2

 cable, the maximum deviation will be 0.25 °C

•  It should be installed in a place protected from vibrations, water and corrosive gases, where the ambient temperature does not 

exceed the value indicated in the technical data.

•  For the reading to be correct, the probe should be used in a place without heat influences apart from the temperature you want to 

measure or control.

•  IP65 protection degree is only valid with the protection cover closed.
•  IP65 protection degree is only valid if the cables enter the device using a tube for electric condu gland with IP65 or above. 

The size of the glands should be suitable for the diameter of the tube used.

•  Do not spray the unit directly with high-pressure hoses, as this could cause damage.

IMPORTANT:

• 

 

Before starting the installation, you must take the advice of local regulations in force.

•   The AUXILIARY relays are programmable, and their operation depends on the configuration.
•   The function of the digital inputs depends on the configuration.
•   The recommended currents and powers are the maximum working currents and powers.

EN 

:  Temperature controller for walk-in coolers and freezers, type AK-RC 204B and AK-RC 205C ......................................................................................................1

ES 

:  Controlador de temperatura para cuartos fríos y congeladores, tipo AK-RC 204B y AK-RC 205C .............................................................................................9

FR : 

Régulateur de température pour chambres froides et congélateurs, type AK-RC 204B et AK-RC 205C ............................................................................... 17

DE : 

Temperaturregler für begehbare Kühl- und Gefrierschränke, typ AK-RC 204B und AK-RC 205C ............................................................................................ 25

PT-BR : Controlador de temperatura para câmaras frigoríficas e congeladores, tipo AK-RC 204B e AK-RC 205C ............................................................................ 33

Wiring

  Always disconnect the power supply to do the wiring.

 

The probes and their cables should 

NEVER

 be installed in a conduit together with power, control or power supply cables.

For disconnection, the power supply circuit must be equipped with a switch of at least 2 A, 230 V, located near the device. The power 

supply cable will be H05VV-F or NYM 1x16/3. The section to be used will depend on the local standard in force, but must never be less 

than 2.5 mm

2

.

Cables for relay or contactor outputs should have a section of 2.5 mm

2

, allow working temperatures equal to or over 70 °C and be 

installed with as few bends as possible.
The 120/230 V~ wiring must be kept clear of any other external element.

The wiring to be done depends on the type of installation. Use the appropriate diagram based on the option selected in the 

wizard. Check the available options on the diagrams included in the controller's packaging.

Wizard refers to a built in tool to guide the user through the set up process.

Maintenance

•  Clean the surface of the unit with a soft cloth, water and soap.
•  Do not use abrasive detergents, petrol, alcohol or solvents, as this might damage the unit.

ENGLISH

Summary of Contents for Optyma AK-RC 204B









































Reviews: