Danfoss MCB 152, Operating Instructions Manual

Page: 43 / 50

LCP Message Description
Status
SO General Reset
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Req. RESET
130BE092.10
The LCP shows this message
after resetting the safety
option with MCT 10 Set-up
Software. After the reset, the
safety option is set to blank
initial state. For more
information, see
chapter 6.1.3 Password
Protection
.
Status
SO Ext.Fail: XXX_STO
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Req. RESET
130BE093.10
The LCP shows this message
when the safety option
detects an external error. The
LCP shows the error number.
For information about the
errors and possible solutions,
see
chapter 9.3.1 List of Error
Conditions . To resume normal
operation, ensure that the
source of the error has
ceased and reset the safety
option.
Status
SO Int.Fail: XXX_STO
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Trip Lock
130BE094.10
The LCP shows this message
when the safety option
detects an internal error. The
LCP shows the error number.
For information about the
errors and possible solutions,
see
chapter 9.3.1 List of Error
Conditions . To resume normal
operation, ensure that the
source of the error has
ceased and power cycle the
safety option.
LCP Message Description
Status
25 Hz
50 %
!1(1)
750 RPM 0.00 A 0.00KW
!Safe Option Failure [W252]
Auto Remote Run on ref.
130BE095.10
The LCP shows this message
when the safety option
detects an issue and cannot
handle the issue as an
internal or external error. A
manual user action is
required in this situation. This
situation can occur in the
following cases:
•
PUST timer expired. To
resume normal operation,
power cycle the safety
option.
•
DI1 offline timer expired.
Test DI1 by activating it.
•
DI2 offline timer expired.
Test DI2 by activating it.
To configure the LCP to show
a dedicated message for each
warning, select
42-86 Safe
Option Info in 0-23 Display
Line 2 Large or in 0-24 Display
Line 3 Large .
Table 9.2 LCP Messages
LCP Message Description
Status
SO Custom. completed
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Req. RESET
130BE096.10
The safety option customi-
sation with MCT 10 Set-up
Software is completed. Reset
the safety option to start the
normal operation.
Status
SO Custom. aborted
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Req. RESET
130BE097.10
The safety option customi-
sation with MCT 10 Set-up
Software was aborted. The
safety option uses the
previous configuration. Reset
the safety option to start the
normal operation.
Status
Safe Opt. initialized
SO RESET required!
!1(1)
0 RPM 0.00 A 0.00KW
!Safe Stop [W68]
Auto Remote SO Req. RESET
130BE098.10
The safety option was
powered up. After the Power
up Self Test (PUST), the safety
option requests a reset.
Table 9.3 LCP Messages, Safe Fieldbus Disabled
Maintenance, Diagnostics an... Operating Instructions
MG37F102 Danfoss A/S © 10/2014 All rights reserved. 41
9 9