background image

LCP Message

Description

Status

SO General Reset

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Req. RESET

130BE092.10

The LCP shows this message
after resetting the safety
option with MCT 10 Set-up
Software. After the reset, the
safety option is set to blank
initial state. For more
information, see

chapter 6.1.3 Password
Protection

.

Status

SO Ext.Fail: XXX_STO

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Req. RESET

130BE093.10

The LCP shows this message
when the safety option
detects an external error. The
LCP shows the error number.
For information about the
errors and possible solutions,
see 

chapter 9.3.1 List of Error

Conditions

. To resume normal

operation, ensure that the
source of the error has
ceased and reset the safety
option.

Status

SO Int.Fail: XXX_STO

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Trip Lock

130BE094.10

The LCP shows this message
when the safety option
detects an internal error. The
LCP shows the error number.
For information about the
errors and possible solutions,
see 

chapter 9.3.1 List of Error

Conditions

. To resume normal

operation, ensure that the
source of the error has
ceased and power cycle the
safety option.

LCP Message

Description

Status

25 Hz

50 %

!1(1)

750 RPM          0.00 A        0.00KW

!Safe Option Failure [W252]

Auto Remote Run on ref.

130BE095.10

The LCP shows this message
when the safety option
detects an issue and cannot
handle the issue as an
internal or external error. A
manual user action is
required in this situation. This
situation can occur in the
following cases:

PUST timer expired. To
resume normal operation,
power cycle the safety
option.

DI1 offline timer expired.
Test DI1 by activating it.

DI2 offline timer expired.
Test DI2 by activating it.

To configure the LCP to show
a dedicated message for each
warning, select 

42-86 Safe

Option Info

 in 

0-23 Display

Line 2 Large

 or in 

0-24 Display

Line 3 Large

.

Table 9.2 LCP Messages

LCP Message

Description

Status

SO Custom. completed

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Req. RESET

130BE096.10

The safety option customi-
sation with MCT 10 Set-up
Software is completed. Reset
the safety option to start the
normal operation.

Status

SO Custom. aborted

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Req. RESET

130BE097.10

The safety option customi-
sation with MCT 10 Set-up
Software was aborted. The
safety option uses the
previous configuration. Reset
the safety option to start the
normal operation.

Status

Safe Opt. initialized

SO RESET required!

!1(1)

0 RPM               0.00 A        0.00KW

!Safe Stop [W68]

Auto Remote SO Req. RESET

130BE098.10

The safety option was
powered up. After the Power
up Self Test (PUST), the safety
option requests a reset.

Table 9.3 LCP Messages, Safe Fieldbus Disabled

Maintenance, Diagnostics an...

Operating Instructions

MG37F102

Danfoss A/S © 10/2014 All rights reserved.

41

9

9

Summary of Contents for MCB 152



















































Reviews: