background image

Introduction

In this installation manual, the word “element” refers 

to both heating cables and heating mats.

If the words “heating cable” or “heating mat” are 

used, the instruction in question applies only to this 

type of element.

The intended uses of the heating elements covered 

by this installation manual are shown in the follow-

ing.

For other applications please contact your local sales 

office.

1�1 

Safety Instructions

Never cut or shorten the heating element 

•  Cutting the heating element will void the 

warranty.

•  Cold leads can be shortened to suit require-

ments.

!

Elements must always be installed according to 

local building regulations and wiring rules as well 

as the guidelines in this installation manual�

•  Any other installation may hamper element 

functionality or constitute a safety risk, and will 

void the warranty.

Elements must always be connected by an  

authorised electrician using a fixed connection�

•  De-energize all power circuits before installa-

tion and service. 

•  Each heating element screen must be earthed 

in accordance with local electricity regulations 

and connected to a residual current device 

(RCD). 

•  RCD trip rating is max. 30 mA.
•  Heating elements must be connected via a 

switch providing all pole disconnection. 

•  The element must be equipped with a correctly 

sized fuse or circuit breaker according to local 

regulations.

1

2

3

4

5

6

7

Summary of Contents for ECaqua










Reviews: