Table of Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5
SMS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
7
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
1
Introduction
The Danfoss Link™ MPB (Mobile Phone Butler) is a GSM device de-
signed for control of the AWAY Function in a Danfoss Link™ sys-
tem. To install and use the Danfoss Link™ MPB correctly, the in-
structions given in this manual are to be strictly followed.
With a simple command sent via SMS, it is possible to turn the
AWAY Function ON/OFF. Via SMS it is also possible to know the
AWAY Function status (ON/OFF).
The Danfoss Link™ MPB is a low-power radio transceiver. When it is
operating, it sends and receives radio frequency energy. Operating
the Danfoss Link™ MPB close to radios, televisions, telephones or
electronic devices in general may cause interference. The Danfoss
Link™ MPB may be subject to interference that affects its perform-
ance.
N
Do not install the Danfoss Link™ MPB
close to pacemakers, auditory prosthe-
ses or medical devices, as the Danfoss
Link™ MPB may interfere with the oper-
ation of these devices.
The Danfoss Link™ MPB operates by
means of a radio signal, no mobile tele-
phone operator is capable of ensuring a
connection at all times. For this reason,
the Danfoss Link™ MPB cannot be used
in life support systems.
2
Installation
For correct operation, the Danfoss Link™ MPB requires a plug-in
SIM card (not included) enabled to receive and send SMS messag-
es. Before inserting the SIM card, disable (if present) the PIN code
protection by using another mobile phone.
Install the Danfoss Link™ MPB on an interior wall sheltered from
the sunlight and all sources of heat and corrosive substances.
Ensure that cables are installed outside possible electromagnetic
fields, in which case, use shielded cables.
Install the Danfoss Link™ MPB within the temperature range of -5
°C to +55 °C.
N
It is important to use the power supply
delivered with the Danfoss Link™ MPB.
Procedure
1. Ensure that the Danfoss Link™ MPB is turned OFF.
2. Insert the SIM card correct in the slot.
3. Screw the antenna on the relative connector (without apply-
ing excessive force).
4. Place the Danfoss Link™ MPB on a firm surface making sure
that a good signal of the GSM operator is present.
5. Connect to Danfoss Link™ SCM (Simple Communication Mod-
ule) or Danfoss Link™ HC (Hydronic Controller) with due ob-
servance of all necessary regulations.
6. Connect the Danfoss Link™ MPB using the power supply,
checking the cables polarity.
Installation Guide
Danfoss Link
™
Mobile Phone Butler
Danfoss Heating Solutions
VIFZZ102
3
