Instructions for installation and use
Akva Lux II VXe
© Danfoss | Produced by Danfoss Redan A/S | 2021.02 | 19
xxxxxxxxxxxxxxx
Check the pump setting by pressing the button once (one constant
pessure). The LEDs will briefly (2 sec.) show the pump setting before
changing back to showing the power consumption.
See fig. 3 - Pump setting view.
If the pump setting does not give the desired distribution of heat in
the rooms of the house, change the pump setting.
See fig. 4 - Recommended pump settings.
Before starting the setting, make clear what the display should
show for the new setting (
see fig. 3
).
To change the pump setting, choose the setting you want (see fig
3), press the button down for more than 2 seconds (less than 10)
and the pump switches to setting selection, the LEDs start flashing
and display the current setting. Then press the button until the LEDs
shows the desired setting. The LEDs flash and when they stop the
new setting is saved. The LEDs return to show power cunstumption.
Please note
that if the LEDs do not flash after 2 seconds, possibly
the pump setting is locked. To unlock, press the button down for
more than 10 seconds. LEDs will flash and the pump is unlocked.
To lock the pump, repeat the procedure.
For more information, se enclosed Grundfos instructions.
Alarm status
In case the 1st LED is red the pump has detected one or more alarms.
See fig. 5 - Alarm status
. When there is no active alarm anymore
the user interface switches back to operation mode shortly and then
showing power consumption.
Fig. 4. Recommended pump settings
Fig. 5. Alarm status
Fig. 3. Pump setting view
* Bronze or stainless steel pump housing
UMP3 15-70 AUTO
Application
Recommended pump mode
Radiator
two-pipe system
1. Auto adapt proportional pressure mode
2. Proportional pressure mode
Radiator
one-pipe system
1. Constant curve mode, speed 1-2-3-4
2. Constant pressure mode
Floor heating
1. Auto adapt, Constant pressure mode
Ventilation
1. Constant curve mode, speed 1-2-3-4
2. Constant pressure mode
Domestic hot water* 1. Constant curve mode, speed 1-2-3-4
Function
Red
Yellow Yellow Yellow Yellow
Blocked
Supply voltage low
Electrical error
SETTING VIEW
SETTING VIEW
PWM PROFILE A: 4M
PWM PROFILE A: 5M
PWM PROFILE A: 6M
PWM PROFILE A: 7M
UPM3 FLEX AS
UPM3 FLEX AS is a flexible solution for boiler
systems now and in the future. It is designed to
work both with and without PWM signal, allow-
ing you to upgrade your systems without having
to change the circulators.
Description
»
Integrated OEM high efficient circulator
»
For flexible use in appliances without PWM
speed control with 4 speeds
»
or in applications with externally controlled
signal with standard PWM profile A for 4 MAX
curves
Exceeding benchmark level of the Ecodesign
requirements in 2015, EEI ≤ 0.20 EN16297/3
UPM3 AUTO
UPM3 AUTO is for all applications in which an
internally controlled pump is needed. It is designed
to be used in appliances or cabinets with increased
ambient temperatures and limited space options;
either in standalone applications or in kit systems
without PWM controller.
Description
»
Standalone OEM high efficiency circulator
»
For standalone applications
»
Optimal for floorheating with a high valve authority
»
Flexibility of settings benefits the OEM production and
the installation in the field
Internally controlled circulators
»
3 control modes
»
10 Curves
»
PLUS AUTO
ADAPT
proportional and constant pressure
»
Substitutes ALPHA2 pumps
MAXIMUM CURVE
PWM PROFILE A
4 M
4 M
5 M
5 M
6 M
6 M
7 M
7 M
PROPORTIONAL
PRESSURE
CONSTANT
PRESSURE
CONSTANT
CURVE
CURVE 1
CURVE 1
4/2 M
CURVE 2
CURVE 2
5/3 M
CURVE 3
CURVE 3
6/4 M
AUTO
ADAPT
AUTO
ADAPT
7/5 M
SETTING OPTIONS
SETTING OPTIONS
AUTO
ADAPT
AUTO
ADAPT
PUMP RUNS
WITHOUT PWM
SIGNAL
PUMP RUNS WITH
PWM SIGNAL
PROP. PRESS.: CURVE 1
PROP. PRESS.: CURVE 2
PROP. PRESS.: CURVE 3
PROP. PRESS.: AUTO
ADAPT
CONST. PRESS.: CURVE 1
CONST. CURVE: CURVE 1
CONST. PRESS.: CURVE 2
CONST. CURVE: CURVE 2
CONST. PRESS.: CURVE 3
CONST. CURVE: CURVE 3
CONST. PRESS.: AUTO
ADAPT
CONST. CURVE: CURVE 1
13. HEATING CIRCUIT, PUMP
