manualshive.com logo in svg

Danfoss AKA 245, Manual

Share
Download
Danfoss AKA 245 Manual Download Page 11

Modem to gateway

Use a standard modem cable.

Supply voltage to the modem must be connected, as illustrated (via DO1). This will permit AKA 245 
to reset the modem. Also, the modem will be switched on and its start controlled, when AKA 245 is 
switched on.

TCP/IP server to gateway and TCP/IP server to PC

So far two servers have been tested:
- ”Lantronix MSS 100” (shown above)

The server to be ordered from a Lantronix dealer.
A 3 m cable with plugs mounted to be ordered from Danfoss. See Ordering.

- ”Digi One SP” (Enclosure about half the size illustrated)

Server to be ordered from a Digi International dealer. Code number is 70001971.
Cable with plug is bypacked.

Supply voltage to the TCP/IP server must be connected, as illustrated (via DO1). This will permit 
AKA 245 to reset the TCP/IP server. Also, the TCP/IP server will be switched on and its start controlled, 
when AKA 245 is switched on.

 

AKA 

245 

Manual RS8DT102 © Danfoss 09/2004 

11

Summary of Contents for AKA 245













































Reviews:

No comments

Brands by name

Popular brands

Load more brands