background image

Step #1 --SECURING BASE FLANGES 

Sit the building boxes in the chosen location. Remove all the 

components from packaging to ensure all components are present by 

checking with the Part List. 

Figure 3  Position of Base Flanges 

Begin by determining exact location of the four (4) corners of the building. Mark front 

edge and side-to-side width of assembly on ground. Drive alignment stakes into the 

ground outside of the markings, and draw alignment strings along both ends and sides 

of the building to the dimensions shown in Figure 3. The outline of the strings will 

represent the final location of the base flanges. The initial location of each Corner 

Base Flanges (

5

R & 

5

L) is critical to the alignment and fit of the frame components 

and cover.

Locate the Left Corner Base Flange and Right Corner Base Flange(

5

R&

5

L). Secure 

the base flanges with Stake Pegs (Part #

17

). Measurements shown in Figure 2 are to 

the center of the upright sockets on each Base Flange. 

The Shelter must be secured to a firm surface that can receive and retain augers and 

pegs firmly in position. The shelter should be installed on FIRM GROUND, not on 

SWAMP, SOFT/WET GROUND. The Base Flanges must be secured so they cannot

be moved. Arches are tensioned at their base as they insert into the Base Plate sockets

.

Summary of Contents for Arched PE















Reviews: