manualshive.com logo in svg

D'Amore engine'ring SMD IM-SG, Owner'S Manual

Share
Download
D'Amore engine'ring SMD IM-SG Owner'S Manual Download Page 13

13 

 

Checking  the  Impedance  of  Speaker  Cables  or 
Signal Cables 

With  the  IM-SG's  low  impedance  mode  and  harness 
compensation it is easy to test the impedance of power wire, 
speaker  cables,  signal  cables,  and  more.    A  few  examples 
are listed below. 

Testing Power Cable 

1.  Follow the instructions on Page 7 for to calibrate the IM-

SG to compensate for test harness impedance.

 

2.  Connect one end of the test harness to one end of the 

power  cable,  and  the  opposite  end  of  the  test  harness 
to  the  other  end  of  the  power  cable.    It  doesn't  matter 
that you cannot fit the entire cable end inside the small 
alligator  clips  on  the  test  harness.    Just  make  a  good 
connection  to  a  number  of  strands  that  comfortably  fit 
the alligator clip.

 

3.  Set the frequency to around 50 Hz

 

4.  If the wire gauge is 4 AWG or larger, it might be hard to 

measure unless measuring a complete spool of at least 
100 feet because the resistance is so small.  

 

5.  It is a good  way to compare two different types of wire 

as long as both spools are the same length.

 

 

Testing Speaker Cable 

1.  Follow the instructions on Page 7 for to calibrate the IM-

SG to compensate for test harness impedance.

 

2.  Connect  the  test  harness  to  the  positive  and  negative 

wires  of  the  speaker  cable  at  one  end.    Short  the 
positive  and  negative  wires  at  the  opposite  end  of  the 
cable. 

 

3.  Set the frequency to around 1 kHz

 

Summary of Contents for SMD IM-SG

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands