Dallas Semiconductor MAXIM DS3112, Manual, Page: 78 / 133

Share

Page: 78 / 133

Dallas Semiconductor MAXIM DS3112 Manual Download Page 78

DS3112

78 of 133

•

•

8 BERT

The BERT block can generate and detect the following patterns:

Pseudorandom patterns 2

7

- 1, 2

11

- 1, 2

15

- 1, and QRSS

•

A repetitive pattern from 1 to 32 bits in length
Alternating (16-bit) words that flip every 1 to 256 words

The BERT receiver has a 32-bit bit counter and a 24-bit error counter. It can generate interrupts on
detecting a bit error, a change in synchronization, or if an overflow occurs in the bit and error counters.
See Section

for details on status bits and interrupts from the BERT block. To activate the BERT

block, the host must configure the BERT mux via the BERT mux control register (Section

). Data can

be routed to the receive side of the BERT from either the T3/E3 framer or from one of the 28 T1 or 16/21
E1 receive ports. Data from the transmit side of the BERT can be inserted either into the T3/E3 framer or
into one of the 28 T1 or 16/21 E1 transmit ports. See

for a visual description of

where data to and from the BERT can be placed.

8.1 BERT Register Description

Register Name:

BERTMC

Register Description:

BERT Mux Control Register

Register Address:

0x6Eh

Bit

# 7 6 5 4 3 2 1

Name

RBPS3 RBPS2 RBPS1

0

—

—

—

RBPS4

RBPS0

Default

0 0 0

—

—

— 0

0

Bit

# 15 14 13 12 11 10 9 8

Name

—

—

—

TBPS4 TBPS3 TBPS2 TBPS1 TBPS0

Default

— — — 0 0 0 0 0

Note: Bits that are underlined are read-only; all other bits are read-write.

Bits 0 to 4: Receive BERT Port Select Bits 0 to 4 (RBPS0 to RBPS4).

These bits determine if data from any of

the 28 T1 or 16/21 E1 receive ports or the T3/E3 receive framer (with or without the overhead bits) will be routed
to the receive side of the BERT. If these bits are set to 11101, only the T3/E3 payload data will be routed to the
receive BERT. If these bits are set to 11110, all T3/E3 data (payload and the overhead bits) will be routed to the
receive BERT.

RBPS4:0

00000 No

Data

01000 Port

8

00001 Port

1

01001 Port

9

00010 Port

2

01010 Port

10

00011 Port

3

01011 Port

11

00100 Port

4

01100 Port

12

00101 Port

5

01101 Port

13

00110 Port

6

01110 Port

14

00111 Port

7

01111 Port

15

10000 Port

16

11000 Port

24

10001 Port

17

11001 Port

25

10010 Port

18

11010 Port

26

10011 Port

19

11011 Port

27

10100 Port

20

11100 Port

28

10101 Port 21

11101 T3/E3 Framer (payload bits only)

10110 Port 22

11110 T3/E3 Framer (p overhead bits)

10111 Port

23

11111 Illegal

State

«
...
76
77
78
79
80
...
»

Summary of Contents for MAXIM DS3112






































































































































Reviews:

No comments