Dallas Semiconductor MAXIM DS3112 Manual Download Page 112

Page: 112 / 133

DS3112

112 of 133

Figure 13-

Table 13-2. AC Characteristics—High-Speed (T3 and E3) Ports

= 3.3V

5%, T

= 0

C to +70

C for DS3112; T

= -40

C to +85

C for DS3112N.)

(See

PARAMETER SYMBOL

MIN

TYP

MAX

UNITS

NOTES

22.4 ns 1,

HRCLK/HTCLK Clock Period

29.1 ns 2,

HRCLK Clock Low Time

HRCLK Clock High Time

HRPOS/HRNEG Setup Time to the
Rising Edge or Falling Edge of
HRCLK

t4 3

HRPOS/HRNEG Hold Time from the
Rising Edge or Falling Edge of
HRCLK

t5 3

Delay from the Rising Edge or
Falling Edge of HTCLK to Data
Valid on HTPOS/HTNEG

t6 3

NOTES:

1) T3

mode.

2) E3

mode.

3) HTCLK is a buffered version of either FTCLK or HRCLK and, as such, the duty cycle of HTCLK is

determined by the source clock.

4) In normal mode, HRPOS and HRNEG are sampled on the rising edge of HRCLK and HTPOS and HTNEG are

updated on the rising edge of HTCLK.

In inverted mode, HRPOS and HRNEG are sampled on the falling edge of HRCLK and HTPOS and HTNEG
are updated on the falling edge of HTCLK.

Figure 13-2. High-Speed (T3 and E3) Port AC Timing Diagram

HRCLK / HTCLK
Normal Mode

HRPOS / HRNEG

HTPOS / HTNEG

HRCLK / HTCLK
Inverted Mode

ls_ac

Summary of Contents for MAXIM DS3112






































































































































Search results

Summary of Contents for MAXIM DS3112

Reviews:

Dallas Semiconductor MAXIM DS3112, Manual, Page: 112 / 133

Search results

Summary of Contents for MAXIM DS3112

Reviews: