background image

12

DAX 3F-I

Troubleshooting

The control unit gives a “Fault” signal for the detector :

•  Check wiring and connections.

•  Possible defect in sensing head connection (APC terminal block).

•  The sensor inside the sensing head may be disconnected or out of order.

The detector gives a non-zero measure :

•  There may be gas in the atmosphere.

The detector gives a non-zero measure even though no gas is present in the atmosphere :

•  Perform full calibration of the detector.

The detector measure is either too high or too low :

•  Perform full calibration of the detector.

The detector gives a null measure although gas is present in the atmosphere :

•  Check wiring and connections.

•  Check if sintered metal filter is not blocked by dust.

•  If sintered metal filter pollution is detected, replace both filter and sensor and perform full cali

-

bration.

Spare parts

Article code

Bracket - mounting kit

B O I 0 0 0 0 0 1 4 8

Cable gland - Ex e M20 (6 - 12 mm) - BRASS 

P R E 0 0 0 0 0 0 2 9

Cable gland - Ex e M20 (6 - 12 mm) - STAINLESS STEEL 

P R E 0 0 0 0 0 0 3 7

Instruction manual

I M P 0 0 0 0 0 0 4 4

Junction box - Ex e

B O I 0 0 0 0 0 1 9 6

Nut - M20 metallic

P R E 0 0 0 0 0 0 2 2

O-ring for cable gland

M E C 0 0 0 0 0 0 1 2

O-ring for sensing head

M E C 0 0 0 0 0 0 4 0

Screw - M4 x 6 mm

V I S V I S 0 0 0 4 2

Sensing head - FPH02 + DAL17

D E T 0 0 0 0 0 0 2 1

Sensing head - FPH02 + DAL21

D E T 0 0 0 0 0 0 2 2

Sensing head - FPH02 + DAL-AC (acetylene)

D E T 0 0 0 0 0 0 2 8

Sensor - DAL17

B A S D E T 0 0 0 2 0

Sensor - DAL21

B A S D E T 0 0 0 3 3

Sensor - DAL-AC (acetylene)

B A S D E T 0 0 0 3 0

Sensor sleeve

M E C 0 0 0 0 0 0 2 8

Sintered metal filter

M E C 0 0 0 0 0 0 1 0

Spanner for sensing head top

O U T 0 0 0 0 0 1 1 3

Terminal block - Ex e 3p

B O R 0 0 0 0 0 0 8 9

Terminal block for earthing - Ex e

B O R 0 0 0 0 0 0 9 1

Summary of Contents for DAX 3F-I

















Reviews: