background image

 

www.dalemans.com

 

 

|

  4

 

 
 

WARNINGS 

 

PRIOR  to  carrying  out  installation,  maintenance,  or  service  operations  on  the 
gas detector ensure that no gas or vapour is present in the surrounding atmos-
phere. 

INSTALLATION,  COMMISSIONING  and  MAINTENANCE  must  be  carried  out  by 
DALEMANS or by an approved service centre only, and in any case by qualified 
personnel who has received a suitable training. 

Gas detection equipment must be calibrated at least once a year to mitigate the 
loss of sensitivity of the sensor.

 

 

  The warranty provided by DALEMANS will be voided if this equipment is not installed, operat-

ed and maintained in strict accordance with these instructions, warnings and within the opera-
tional limits stated. 

  By  respecting  these  instructions  you  ensure  the  proper  operation  of  the  equipment.  Should 

you require any further information about the installation, the use or the maintenance of this 
equipment, do not hesitate to contact DALEMANS. 

  Always follow the recommendations hereafter so as to avoid premature ageing of the sensor 

and to guarantee its optimal operation. These recommendations are general directives. 

  Refer  to  local  regulations  in  force  before  proceeding  with  installation  works  (i.e.  standards 

IEC 60079-14  and  IEC  60079-29-2).  Local  regulations  have  always  precedence  on  the  rec-
ommendations of the manufacturer. 

  Maintenance must be performed according to the procedure given by DALEMANS or his local 

representative. Maintenance or service attempts without observing these instructions or with-
out the assistance of DALEMANS may prevent the equipment from working properly and from 
ensuring the safety of the occupants of the monitored premises. 

  Modification,  disassembling  and  total  or  partial  destruction  of  this  equipment  may  invalidate 

the essential safety requirements of the whole plant. 

  Use only DALEMANS original replacement parts. The use of non-original parts may invalidate 

the certification and warranty of the equipment. 

 

LIMITATIONS 

  Persistent exposure to  high levels  of toxic gas will  shorten the sensor life. Sensors may be 

cross sensitive to other gases. 

  Long-term  unpowered  storage  might  shorten  the  electrochemical  sensor  life.  Avoid  discon-

necting the electrochemical sensor from the amplifier Printed Circuit Board. 

  Gas detectors should be installed as late as possible in any program of construction opera-

tions (i.e. construction of a new plant, refitting or maintenance) but before the presence of gas 
or vapours in the system, so as to avoid damage to sensors resulting in particular from such 
activities as welding and painting. If already installed, detectors should be protected by an air-
tight seal to avoid contamination during construction works, and should be clearly marked as 
being non-operational. 

  Gas detectors must be protected from direct sunlight, vibrations and mechanical impacts. 

 

 

Summary of Contents for DAT 420





















Reviews: