Daktronics SPORTSOUND 1500HD, Installation Manual

Page: 39 / 54

W/O MESH "GRILLE"
SIDE VIEW
ACOUSTICAL MESH "GRILLE"
ARTWORK TO BE APPROVED BY
CUSTOMER.
BOTTOM VIEW
FRONT OF SOUND SYSTEM
(2) DAKTRONICS LOW-RANGE
SPEAKER CABINETS
(5) DAKTRONICS MID-RANGE
SPEAKER CABINETS. CAPABLE
TO TILT 0-15 DEGREES DOWN.
(1) DAKTRONICS HIGH-RANGE
SPEAKER CABINET LINE ARRAY.
TILTS W/ MID-RANGE CABINET.
ISOMETRIC VIEW
(4) 5/8" REMOVEABLE LIFT EYES. DESIGNED FOR
MAX. 45° SLING ANGLE. WHEN POSSIBLE
USE A PROPERLY SIZED SPREADER BEAM
WHEN LIFTING SOUND SYSTEM.
SIDE VIEW
NOTES:
1.0 REFERENCE
1.1 REFER TO DAKTRONICS RISER DIAGRAM 1340-R10B-329134
FOR ALL ELECTRICAL POWER AND DATA SPECIFICATIONS.
1.2 THE SHOWN SYSTEM MUST BE APPROVED BY THE
CUSTOMER AND ALL ATTACH-TO STRUCTURE MUST BE
CERTIFIED IN THE STATE IN WHICH IT IS INSTALLED BY A
QUALIFIED STRUCTURAL ENGINEER BEFORE FABRICATION OR
ERECTION.
2.0 GENERAL NOTES
2.1 ALL DIMENSIONS ARE IN FEET AND INCHES.
2.2 REFER TO INSTALLATION AND MAINTENANCE MANUAL FOR
COMPLETE INSTALLATION INSTRUCTIONS.
3.0 SOUND CABINET NOTES
3.1 DAKTRONICS SOUND CABINET IS STEEL CONSTRUCTED
SKELETON WITH METAL PANELING FASTENED TO ITS EXTERIOR.
3.2 LIFT PLATES ARE PROVIDED BY DAKTRONICS. WHEN LIFTING
USE 45° OR GREATER, FROM THE HORIZON, CABLE SYSTEM.
4.0 STRUCTURAL NOTES
4.1 ALL STRUCTURAL STEEL SHALL BE ASTM A36, EXCEPT:
TUBING SHALL BE A500-B.
4.2 THE SOUND CABINET HAS BEEN DESIGNED TO WITHSTAND
UP TO A *150MPH (3-SEC GUST) DESIGN WIND SPEED WTIH AN
OVERALL MAXIMUM DESIGN PRESSURE OF 88 PSF ACCORDING
TO ASCE 7-05 (EXPOSURE C).
*REFER TO TABLE FOR MAXIMUM DISTANCE OF FRONT WELD
CONNECTION.
4.3 THE DESIGN WIND PRESSURE WERE SHIFTED AND ADJUSTED
TO ACCOUNT FOR ASCE 7 PRESCRIBED OFFSET EFFECTS.
4.4 THE SOUND CABINET HAS BEEN DESIGNED TO SUPPORT A
FLOOR LIVE LOAD OF 90 PSF TO ACCOUNT FOR THE WEIGHT OF
THE SPEAKERS AND ANY SERVICE PERSONNEL.
4.5 THE SOUND CABINET HAS BEEN DESIGNED TO SUPPORT A
DESIGN ROOF SNOW LOAD OF 30 PSF.
4.6 THE SOUND CABINET HAS BEEN DESIGNED TO SUPPORT A
LATERAL SEISMIC LOADING EQUAL TO 2.0 TIMES GRAVITY.
4.7 FABRICATION AND ERECTION SHALL CONFORM TO THE
LATEST EDITION OF AISC SPECIFCATIONS.
4.8 ALL WELDING (SHOP AND FIELD) SHALL BE PERFORMED IN
ACCORDANCE WITH AWS D1.1-LATEST EDITION SPECIFICATIONS
BY A CERTIFIED WELDER USING E70XX ELECTRODES.
5.0 PROJECT RESPONSIBILITY
5.1 DAKTRONICS' AND CUSTOMER SUBCONTRACTORS SHALL
VERIFY ALL EXISTING CONDITIONS AND DIMENSIONS PRIOR TO
INSTALLATION.
5.2 ALL SUBCONTRACTORS SHALL PERFORM WORK IN
ACCORDANCE WITH OSHA REQUIREMENTS AND ANY LOCAL
CODES THAT APPLY.
5.3 EACH SUBCONTRACTOR IS SOLELY RESPONSIBLE FOR
JOBSITE SAFETY.
5.4 ERECTION SUBCONTRACTOR IS SOLELY RESPONSIBLE FOR
DESIGNING AND PROVIDING TEMPORARY BRACING.
5.5 EACH SUBCONTRACTOR IS RESPONSIBLE FOR THE REMOVAL
AND DISPOSAL OF WASTE MATERIALS ON THE JOBSITE.
TYPICAL WELD DETAIL FOR EACH
MAIN BOTTOM TRANSVERSE MEMBER.
TOTAL SOUND SYSTEM WEIGHT: 4000 LBS
POWER IN LOCATION.
20 AMP 208-240VAC @3
REQUIRED
SHEET
SPORTSOUND
2000HD
STANDARD SHOP
502
DATE: TITLE:
SIGNED:
COMPANY:
APPROVED AS NOTED & RESUBMIT
APPROVED AS NOTED
APPROVED
SUBMITTAL APPROVAL
SPORTSOUND CONTROL ENCLOSURE.
SPEAKER DATA IN LOCATION
(1) W-1614, AUDIO CABLE, 2 PAIR, 22AWG
(1) W-1489, FIBER CABLE, 6 CORE
CABLE PROVIDED BY DAKTRONICS
INSTALLED BY DAKTRONICS
SUBCONTRACTOR.
22'-0" [6706mm] OVERALL
1/4 2" MIN
TYPICAL ON ALL
10 LOCATIONS
CONCEALED FASTENER 0.063"
ALUMINUM PANELS ATTACHED
ON SIDES AND BACK.
0.125" ALUMINUM PANELS
ATTACHED TO TOP
OF CABINET.
22'-0" [6706mm] OVERALL
0'-1 3/8" [35mm]
SIDE BORDER.
(TYP.)
0'-3 5/8" [93mm]
TOP BORDER
10'-5 3/8" [3185mm]
FRONT LIFT EYES
0'-3 5/8" [91mm]
BTM BORDER
11'-2 1/8" [3407mm]
REAR LIFT EYES
W/O MESH "GRILLE"
6'-0" [1829mm]
OVERALL
0'-0 3/4" [19mm]
DOOR
5'-4 7/8" [1648mm]
5'-4 7/8" [1648mm] 5'-4 7/8" [1648mm]
5'-4 7/8" [1648mm]
DIM "A"
SEE TABLE
TOP VIEW
3'-6" [1066mm]
OVERALL W/O DOORS
22'-0" [6706mm]
OVERALL WIDTH
REAR VIEW
STEEL TUBE CONSTRUCTED SOUND
CABINET. SEE DAKTRONICS STRUCTURAL
DRAWINGS FOR FURTHER MEMBER
SIZES AND DETAILS.
(8) REAR ACCESS DOOR FOR SERVICE
OF INTERNAL COMPONENTS IN CABINET.
DOORS CAN BE REMOVED BY TURNING
LATCHES WITH A STRAIGHT EDGE
SCREWDRIVER AND LIFTING DOOR
OUT OF BOTTOM CHANNEL.
1'-8 3/8" [517mm]
TYP.
DIM "A"
APPROX.
2'-0" [610mm]
RECOMMENDED
FOR SERVICE
VARIOUS
DISPLAYS
SS2000HD
SOUND
SYSTEM
3'-6" [1066mm]
6'-0" [1829mm]
DIM "B"
NOTES:
DIM "A" REPRESENTS THE MAXIMUM DIMENSION FROM THE
FRONT OF SOUND SYSTEM TO FRONT WELD LOCATION OF
"ATTACH-TO STRUCTURE" PER DESIGN WIND PRESSURE.
DIM "B" REPRESENTS THE MAXIMUM DIMENSION FROM THE
BACK OF SOUND SYSTEM TO BACK WELD LOCATION OF
"ATTACH-TO STRUCTURE" PER DESIGN WIND PRESSURE.
THE "ATTACH-TO STRUCTURE" SHOWN IS FOR CONCEPTUAL
PURPOSES ONLY. THE APPROPRIATE LOADING CONDITIONS
AND THE SIZE OF THE "ATTACH-TO STRUCTURE" SHALL BE
EVALUATED FOR EACH USE OF THIS SYSTEM AND IS NOT
EVALUTED IN THIS DRAWING.
DIM "B"
SEE TABLE
0'-7 7/8" [199mm]
2'-7 1/8" [790mm]
LIFT EYE
SPACING
FRONT "GRILLE" FRAME CAN BE REMOVED
FOR SPEAKER MESH RE-INSTALLATION.
(10) 3/8" HARDWARE SETS ON TOP &
(10) 3/8" HARDWARE SETS ON BTM
SECURE FRAME TO STEEL CABINET.
"GRILLE" FRAME APPROX. 180 LBS.
6'-0" [1829mm]
OVERALL
W/0 LIFT EYES
POWER/SIGNAL
CONTROL ENCLOSURE
4'-4 5/8" [1337mm]
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS
DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT
REPRODUCE BY ANY MEANS WITHOUT THE EXPRESSED
WRITTEN CONSENT OF DAKTRONICS, INC.
COPYRIGHT 2010 DAKTRONICS, INC. DO NOT SCALE DRAWING
DAKTRONICS, INC.
BROOKINGS, SD 57006
CH
DATE: REV BY:
05 29 APR 10
KCS
DECREASED THE NUMBER OF DOORS FROM
9 TO 8.
UPDATED HANDLE WITH RECESSED VERSION.
DATE: REV BY:
06 12 JAN 11 JLR
UPDATED PER NEW REAR ACCESS DOOR
ADDED MESH FRAME LIFT EYE NOTE
DATE: REV BY:
01 30 MAY 08 KCS
UPDATED DRAWING WITH LATEST MODEL
ADDED LIFT POINTS
UPDATED HIGH FREQUENCY ARRAY
DATE: REV BY:
02 13 APR 09
KCS
CHNAGED W-1456 TO W-1489
REMOVED CONDUIT AND ADDED CABLE TRAY.
CHANGED W-1614 TO QUANTITY OF 1.
DATE: REV BY:
03 10 NOV 09
KCS
ADDED QUANTITY @3 TO 20 AMP POWER
REQUIREMENTS
DATE: REV BY:
04 30 DEC 09
DMT
REDUCED DEPTH OF CABINET, REDUCED WEIGHT,
REAR ACCESS DOORS, ALUM SIDING, REVISED MTG
DESIGN
TYPE
SCALE:
PROJ:
TITLE:
DESIGN:
DRAWN: DATE:
FUNC SHEET SIZE JOB NO: REV
SPORTSOUND SYSTEMS
SHOP DRAWING; SOUND SYSTEM; 2000HD
DTREML 18 JAN 07
P1340 E 10 C
1/4"=1'
DTREML
330901
09 001
NOTE:
THE 2 LIFT EYES ON THE FRONT MESH FRAME SHOULD NOT BE
USED WHEN LIFTING THE CABINET INTO POSITION. THESE ARE TO
BE USED ONLY WHEN REMOVING THE MESH FRAME FROM THE
CABINET FOR MAINTENANCE PURPOSES.
LEAVE THESE 2 LIFT EYES ON THE MESH FRAME AFTER
INSTALLATION IS COMPLETE.
DATE: REV BY:
07 9 JUN 11 MBJ
UPDATED TOP, FRONT, BTM & SIDE VIEWS
DATE: REV BY:
08 23 OCT 12 KCS
UPDATED CABINET VIEWS WITH NEW CRTL ENCL.
CRTL ENCL LOCATION
CUT GRATING AS NEEDED
TO CONNECT POWER AND
SIGNAL
21'-9" [6628mm]
MESH "GRILLE" COPY AREA
5'-4 3/4" [1644mm]
MESH "GRILLE"
COPY AREA
DATE: REV BY:
09 18 JUL 13
KCS
UPADTED REAR ACCESS DOOR VIEWS WITH NEW
LATCH AND DOOR HANDLE