Daktronics P1192, Installation Manual

Page: 29 / 34

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS
DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT
REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS
WRITTEN CONSENT OF DAKTRONICS, INC.
COPYRIGHT 2015 DAKTRONICS, INC.
DAKTRONICS, INC.
BH
MOUNTING BRACKET
DRILL 1/4" HOLES
REAR
OF
DISPLAY
0'-3"
INSTALLATION PROCEDURE:
1. OPEN THE RIGHT DIGIT AND REMOVE THE COVER FROM THE DRIVER.
2. DRILL A 7/8" HOLE IN THE RIGHT SIDE OF THE DISPLAY PER THE DIMENSIONS SHOWN IN DETAIL A.
3. INSERT INCLUDED CONDUIT CONNECTORS INTO THE 7/8" HOLE AND INTO THE BOTTOM OF THE HORN AS SHOWN IN DETAIL B.
4. POSITION THE HORN MOUNTING BRACKET PER DETAIL B.
5. MARK THE MOUNTING BRACKET HOLE LOCATIONS ONTO THE SIDE OF THE DISPLAY.
6. DRILL 1/4" HOLES WHERE THE MOUNTING BRACKET HOLES WERE MARKED ON THE SIDE OF THE DISPLAY.
7. MOUNT THE HORN MOUNTING BRACKET WITH THE INCLUDED 1/4" HARDWARE.
8. ATTACH THE HORN TO THE BRACKET WITH INCLUDED 1/4" HARDWARE. *THE WIRES PROTRUDE OUT THE BOTTOM OF THE HORN. MAKE
SURE THE HORN IS MOUNTED WITH THE BOTTOM DOWN.
9. THE GROUND WIRE WILL NOT BE CONNECTED, CUT THE GREEN WIRE AS SHORT AS POSSIBLE.
10. ROUTE THE WIRES THROUGH THE CONDUIT AND INTO THE DISPLAY.
11. ONCE THE HARNESS HAS BEEN RUN THROUGH THE CONDUIT, CONNECT THE CONDUIT TO THE CONDUIT CONNECTORS IN THE SIDE OF
THE DISPLAY AND THE BOTTOM OF THE HORN.
WIRING INSTRUCTIONS:
1. USE HARNESS 0A-1192-1686 (2-WIRE BLK AND WHT @10' LONG) AND TERMINATE THE BLACK WIRE AND THE WHITE WIRE FROM THIS
HARNESS TO THE TWO WIRES COMING OUT OF THE BOTTOM OF THE HORN. USE THE INCLUDED E-1044 BUTT SPLICES TO MAKE THIS
TERMINATION. NOTE: WIRES FROM THE HORN CAN CONNECT TO EITHER THE BLACK OR WHITE WIRES THIS CONNECTION IS
INTERCHANGEABLE.
2. REFERENCE SCHEMATIC DWG-132173 FOR CONNECTIONS MADE INSIDE DISPLAY TO THE HORN CARD (0P-1192-0399) PROVIDED IN HORN
ASSY KIT.
3. ATTACH THE COVER ONTO THE DRIVER AND ATTACH THE REMOVED DIGIT TO THE DISPLAY FACE.
INSERT CONDUIT
CONNECTORS INTO THE
DISPLAY AND HORN
DRILL 7/8" HOLE
DRAWN: DATE:
SHEET JOB NO: REV
SCOREBOARDS
HORN MTG INSTRUCTIONS; 120V, TI-2003, GYRUS DRIVER
KSCHNABEL 8 MAY 15
P1782 E 10 B
1=5
KSCHNABEL
3054691
00
P1
(DRIVER SHOWN W/O COVER)
J1
J3
J2
(TO TRUMPET HORN)
J5
DRIVER COMPONENTS INSTALLATION PROCEDURE:
1. FROM THE 0A-1192-1685, HORN INTERFACE CARD ASSY. MOUNT 0P-1192-0399
HORN SWITCH CARD USING HS-1042 SPACER & HC-1238 LOCK NUT.
2. PLUG TI-2003 HORN SIGNAL HARNESS (0A-1192-0393) PLUG P5 INTO JACK J5 ON
THE DRIVER AND PLUG P2 INTO JACK J2 OF 0P-1192-0399 HORN SWITCH CARD.
3. PLUG POWER ADAPTER HARNESS 0A-1782-0299 PLUG P42 INTO JACK J42 ON
THE HARNESS LEAVING THE DIGIT DRIVER.
4. CONNECT PLUG P1 OF THE POWER HARNESS COMING FROM ADAPTER
HARNESS 0A-1782-0299 INTO JACK J1 ON THE HORN INTERFACE CARD.
5. CONNECT HORN CABLE PLUG P3 INTO JACK J3 OF THE 0P-1192-0399 AND THE
OPPOSITE END ON TO THE HORN.
SPACER NUT
P2
STEP 1
STEP 2
J42
J42
STEP 3
STEP 4
STEP 5
NOTES:
-THIS DRAWING DOES NOT DEPICT THE
ACTUAL LAYOUT OF COMPONENTS.
-THIS DRAWING EXPLAINS HOW THE HORN
COMPONENTS ARE CONNECTED TO EACH
OTHER.
GYRUS DIGIT DRIVER