background image

Introduction

2

Resources

Figure 2

 illustrates a Daktronics drawing label. 

This manual refers to drawings by listing the last 

set of digits. In the example, the drawing would 

be referred to as 

DWG-1007804

. All references to 

drawing numbers, appendices, figures, or other 

manuals are presented in bold typeface. 

Any drawings referenced in a section are listed 

at the beginning of it as shown below: 

Reference Drawing:

System Riser Diagram .......................................................................................

DWG-1007804

Daktronics identifies manuals by the DD or ED number located on the cover page. 

Ensure all applicable materials have been gathered before beginning the installation. 

Contact a Daktronics sales coordinator or project manager. 

Daktronics Nomenclature

Most display components have a white label that lists the part 

number (

Figure 3

). Part numbers will also appear on certain drawings. 

If a component is not found in the 

Replacement Parts (p�8)

, use 

the label to order a replacement. Refer to 

Section 4: Daktronics 

Exchange and Repair & Return Programs (p�9)

 if replacing or 

repairing any display component. 

Main Component Labels

Part Type

Part Number

Individual circuit board

0P-XXXX-XXXX

Assembly; a collection of 

circuit boards

0A-XXXX-XXXX

Wire or cable

W-XXXX

Fuse

F-XXXX

Transformer

T-XXXX

Metal part

0M-XXXXXXX

Fabricated metal assembly

0S-XXXXXX

Specially ordered part

PR-XXXXX-X

Display Controllers

Daktronics TI-2002 timing displays are designed for use with an All Sport

®

 1600 or 5000 

console. Both controllers use keyboard overlays (sport inserts) to control numerous sports 

and display models. Refer to the following manuals for operating instructions: 
• 

All Sport 1600 Series Control Console Operation Manual (ED-12462)

• 

All Sport 5000 Series Control Console Operation Manual (ED-11976)

These manuals are provided on a CD with the control console and they are also 

available online at 

www.daktronics.com/manuals

.

Drawing Number

Figure 2: 

Drawing Label

0P-1127-0024

SN:  

     2465

02/19/12 Rev. 1

Figure 3: 

Part Label

Accessory Labels

Component

Label

Termination block for 

power or signal cable

TBXX

Grounding point

EXX

Power or signal jack

JXX

Power or signal plug for 

the opposite jack

PXX

Summary of Contents for P1152



























Reviews: