Dakota Digital BIM-RGB Manual Download Page 9

MAN # 650810 

 
 

Troubleshooting guide

PROBLEM

 

POSSIBLE CAUSE(S)

 

POSSIBLE SOLUTIONS(S)

 

LED

’s not lighting up 

No power to the BIM-RGB 

Poor connection on the +, R, G or B 
outputs 

BIM-RGB is in music mode 

Check power and ground connections into the BIM_RGB 

Check the connections to the LED’s 

 
In music mode the LED’s will flash on with music. Go into the settings 
and make sure music mode is off. If you tap on the BIM-RGB case by 
the microphone input and the L

ED’s flash this is most likely the 

problem. 

PROBLEM

 

POSSIBLE CAUSE(S)

 

POSSIBLE SOLUTIONS(S)

 

LED’s not flashing in music 
mode 

BIM-RGB is not in a location where the 
microphone can pick up the music       

 
The LED outputs are not turned on 

Be sure the BIM-RGB is located where it can pick up sound from a 
speaker. If you tap on the BIM-RGB case by the microphone input the 
LED’s should flash. If they do this is most likely the problem 

Check the On/Off setting in the app, or toggle the On/Off switch if 
using the optional switch panel. If you toggle the music mode switch 
the LED’s should turn on and off if no music is playing and the LED 
outputs are turned on. 

LED color not synchronized to 
the gauge 

Bad connection to the gauge 

 

 
Sync mode not enable 

Check the cable between the gauge and BIM-

RGB. If LED’s are white 

this is the default color and would indicate this may be the problem. 
The module defaults to standalone mode if no message from the 
gauge is detected after 10 seconds. 

Check the synch setting in the app, or if using the optional switch 
panel press the color switch for greater that 3 seconds to change 
modes 

 

 

 

Summary of Contents for BIM-RGB













Reviews: