background image

7

4. To cancel the reminder beep press the “A” button for 0.5 seconds.

5.  You can also use jumper “J2” (Figure 1-5) in the receiver to select which zones will have the 

reminder beep. If the jumper covers both pins for a zone, that zone will have the reminder beep. 

If the jumper is on only one pin, the zone will not have the reminder beep. 

exit delay:

The receiver can be programmed to have a 5 minute exit delay where it will not receive a signal 

from selected transmitters.

1. The jumper “J3” (Figure 1-6) can be used to determine which zone(s) you would like to use with 

the exit delay. To use the exit delay set the jumper to cover both pins for the desired zone(s).

2. To start the exit delay press the “B” button (Figure 1-9) for 0.5 seconds and release. The green led 

will flash for 5 minutes and during this time no signals will be received from the selected zones.

NOTE: Whenever a change is made to the jumpers or the dip switches, the receiver must be 

turned “OFF” and then back “ON” to operate properly.

Frequency: 433.92 MHz

Operating voltage: 12VDC

12 volt DC output current: 400 mA maximum

Relay rating: 24VDC at 3 Amp

DCR2500 Manual.indd   7

4/6/2010   8:23:35 AM

Summary of Contents for DCR-2500









Reviews: