background image

The 

UT 4000 

is an easy-to-use universal transmitter that operates on a 3-volt lithium 

battery and has several different methods of activation.  The UT 4000 has a push button 

that can be used as a panic button or a wireless doorbell.  There is also a magnetic door/

window  contact and inputs that can be used with any sensor contacts.  The sensor will 

send a signal back to one of our 4000 Series receivers about a mile away.*

The 

BBT 4000 

is a solar powered wireless infrared brake beam sensor.  It is easy to 

install and requires no wiring.  The sensors are powered by built-in lithium ion batter-

ies that are recharged through the solar panels during the day.  The infrared sensing 

terminals can be mounted up to 300 feet apart.  Installation time can be as little as a 

few minutes.  The sensor will send a signal back to one of our 4000 Series receivers 

about a mile away.*

The 

DCHT 4000 

is a very reliable and easy-to-install driveway alarm.  This transmitter 

operates on one 9-volt battery and has 25’ of 3/8” diameter hose that lies across the 

drive.  When a vehicle drives over the hose the sensor will send a signal back to one of 

our 4000 Series receivers about a mile away.*

              

 *

Although the maximum range is about one mile, obstructions such as hills, trees, metal siding,

              and stucco can all reduce the range.  Metal posts may interfere with the transmitter’s radio signal.

Go to www.dakotaalert.com for

Additional

 

4000 Series

 

Products

Summary of Contents for DCPT-4000













Reviews: