background image

daka 832 furnace manual_3-18-13 

Page 14 of 14 

 

September 26, 2012, Revised March 18, 2013 

 

LIMITED WARRANTY 

 

DAKA Corporation warrants the combustion chambers of its supplementary 
furnaces to be free of defects in material or workmanship for five years from date of 
sale; all other components, including electronics, gaskets and grates are covered in 
the same manner for a period of one year. 

 

DAKA will repair or replace defective components, at our option, at no charge for 
parts and labor, and will pay freight charge for one-way shipment for warranty 
claims during first year.  In second and subsequent years, only parts and labor will 
be provided at no charge.  DAKA is not responsible for installation or dismantling 
costs. 

Warranty void if unit is used in other than residential service connected to 
conventional basement-type up flow central heating system, if non-approved fuels 
are used in firing of units, or if unit is damaged due to accident, improper 
installation or negligence. 

 

For service under this warranty, contact selling dealer or DAKA Corporation, 
Customer Service Dept., 955 Industrial St NE, Pine City MN 55063; Telephone 
(320) 629-6737. 

 

Implied Warranties including that of merchantability are expressly limited in 
duration to the duration of this warranty.  DAKA Corporation disclaims any 
responsibility for consequential damages.  Some states do not allow limitations on 
how long an implied warranty lasts, or the exclusion or limitation of incidental or 
consequential damages, so this limitation and exclusion may not apply to you.  

 

This warranty gives you specific legal rights, and you may also have other rights 
which vary from state to state. 

 

This is our exclusive written warranty.

 

 

Summary of Contents for 832



















Reviews: