background image

 DTP7H-D hardware user

’s manual 

 

DAINCUBE  Corp.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 / 35

 

 

Never lay the device close to heat sources or into direct sunlight. 

 

Avoid exposing the device to mechanical vibrations, excessive dust, and humidity or to strong 
magnetic fields. 

 

Make sure that no foreign objects or liquids can penetrate into the device. 

 

Wipe the power plug with a clean, dry cloth periodically to eliminate dust. 

 

Always pay special attention to the robot’s movement in the Teaching Mode. 

 

3.  Warranty and warranty coverage 

 

The Teaching pendant you purchased has been delivered upon completion of our strict shipping test. 

 

3.1.  Warranty period 

  

The warranty period is as follows: 

  

 

12 months after our shipment.  

 

3.2.  Scope of the warranty 

 

Where a defective condition occurs during proper use conditions and obviously under the responsibility of 
the manufacturer, within the term above, we shall repair the product without charge. 
 
However, any items that apply to the following are excluded from the warranty coverage.  

 

 

The warranty is not valid if the defect is due to accidental damage, mishandling, misuse, voltage 
fluctuation, high/low voltage or natural disaster. 

 

If the product is repaired or tried to repair from unauthorized personal/Repair Shop. 

 

If the product serial number is tempered. 

 

The product is defective due to wear of parts, which can be considered as consumable parts by the 
nature. (such as a cable) 

 

Defects resulting from changes over time such as natural color fading of paint. 

 

Defects resulting from mishandling or improper use. 

 

Defects resulting from an inadequacy or error in maintenance and inspection. 

 

Defects resulting from the use of any part other than our genuine parts. 

 

Defects resulting from a modification not approved by us or our dealers. 

 

 Only a delivered product shall be singly warranted, and no damage induced by the defect of the delivery 
product can be warranted. For repair, transport the product to our factory. 

 

3.3.   Service coverage 

 

The cost of a delivered product does not include expenses for program creation and engineer dispatching. 
Therefore, the following are charged separately even within the warranty term: 

 

 

Maintenance and inspection. 

 

Technical guidance and technical training in the operating instructions. 

 

Technical guidance and technical training on program-related matters such as program creation.

 

 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for DTP7H-D




































Reviews: