background image

3

English

Outdoor Unit Installation Drawings

CAUTION

Set the piping length from 
1.5m to 15m.

Wrap the insulation pipe with 
the finishing tape from bottom 
to top.

In sites with poor drainage, use 
block bases for outdoor unit. 
Adjust foot height until the unit 
is leveled. Otherwise, water 
leakage or pooling of water may 
occur.

Where there is a danger of the unit 
falling, use foot bolts, or wires.

Allow space for piping 
and electrical servicing.

250mm from w

all

unit: mm

O.D. 9.5mm

Gas pipe

Liquid pipe

O.D. 6.4mm

20g/m

Max. allowable length

12m

15m

Max. allowable height

Additional refrigerant 
required for refrigerant 
pipe exceeding 
10m in length.

*

Be sure to add the proper amount of additional refrigerant.

Failure to do so may result in reduced perfomance.

*

The suggested shortest pipe length is 1.5m, in order to avoid 

noise from the outdoor unit and vibration. 

(Mechanical noise and vibration may occur depending on how 

the unit is installed and the environment in which it is used.)

1.5m

Min. allowable length

470

(Foot bolt-hole cent

res)

(From unit’s side)

96

Foot bolt-hole 

centres

300

How to remove the stop 
valve cover.

Remove the screw on the 
stop valve cover.
Slide the lid downward 
to remove it.

How to attach the stop 
valve cover.

Insert the upper part of 
the stop valve cover into the 
outdoor unit to install.
Tighten the screws.

Stop valve cover

*

3P291651-9T.book  Page 3  Tuesday, December 9, 2014  2:55 PM

Summary of Contents for RXB20C5V1B



















Reviews: