background image

Installation and operation manual

46

10T8Y1B

VRV-W IV System Air Conditioner

4P399208-1 – 2015.01

WARNING

If you detect any abnormality such as smell of fire, 
turn off the power supply and call your dealer for 
instructions.

Do not place objects in direct proximity of the outdoor 
unit and do not let leaves and other debris accumulate 
around the unit. Leaves are a hotbed for small 
animals which can enter the unit. Once in the unit, 
such animals can cause malfunctions, smoke or fire 
when making contact with electrical parts.

Ask your dealer for improvement, repair, and 
maintenance. Incomplete improvement, repair, and 
maintenance may result in a water leakage, electric 
shock and fire.

Do not insert fingers, rods or other objects into the air 
inlet or outlet. When the fan is rotating at high speed, 
it will cause injury.

Never let the indoor unit or the user interface get wet. 
It may cause an electric shock or a fire.

Never use a flammable spray such as hair spray, 
lacquer or paint near the unit. It may cause a fire.

Never touch the air outlet or the horizontal blades 
while the swing flap is in operation. Fingers may 
become caught or the unit may break down.

Never replace a fuse with a fuse of a wrong ampere 
ratings or other wires when a fuse blows out. Use of 
wire or copper wire may cause the unit to break down 
or cause a fire.

To prevent refrigerant leak, contact your dealer. When 
the system is installed and runs in a small room, it is 
required to keep the concentration of the refrigerant, if 
by any chance coming out, below the limit. Otherwise, 
oxygen in the room may be affected, resulting in a 
serious accident.

The refrigerant in the air conditioner is safe and 
normally does not leak. If the refrigerant leaks in the 
room, contact with a fire of a burner, a heater or a 
cooker may result in a harmful gas.
Turn off any combustible heating devices, ventilate 
the room and contact the dealer where you purchased 
the unit.
Do not use the air conditioner until a service person 
confirms that the portion where the refrigerant leaks is 
repaired.

Improper installation or attachment of equipment or 
accessories could result in electric shock, short circuit, 
leaks, fire or other damage to the equipment.

Be sure to use only accessories and spare parts 
made by Daikin which are specifically designed for 
use with the equipment and have them installed by a 
professional.

Ask your dealer to move and reinstall the air 
conditioner. Incomplete installation may result in a 
water leakage, electric shock, and fire.

Do not place a flammable spray bottle near the air 
conditioner and do not use sprays. Doing so may 
result in a fire.

Before cleaning, be sure to stop the operation, turn 
the breaker off or pull out the supply cord. Otherwise, 
an electric shock and injury may result.

Do not operate the air conditioner with wet hands. An 
electric shock may result.

Do not place appliances which produce open fire in 
places exposed to the air flow from the unit or under 
the indoor unit. It may cause incomplete combustion 
or deformation of the unit due to the heat.

Do not wash the air conditioner with water. Electric 
shock or fire may result.

WARNING

Do not install the air conditioner at any place where 
flammable gas may leak out. If the gas leaks out and 
stays around the air conditioner, a fire may break out.

In order to avoid electric shock or fire, make sure that 
an earth leak detector is installed.

Be sure the air conditioner is electrically earthed.

In order to avoid electric shock, make sure that the 
unit is grounded and that the earth wire is not 
connected to gas or water pipe, lightning conductor or 
telephone earth wire.

Do not place a flower vase or anything containing 
water on the unit. Water may enter the unit, causing 
an electric shock or fire.

Avoid placing the controller in a spot which can be 
splashed with water. Water entering the machine may 
cause an electric leak or may damage the internal 
electronic parts.

This unit is made for indoor use. The unit should be 
installed in a machine room.

In case of a natural disaster and the unit gets 
submerged, do not operate the unit, or otherwise a 
malfunction, electric shock or fire may occur.

Watch your step at the time of air filter cleaning or 
inspection.

CAUTION

It is not good for your health to expose your body to 
the air flow for a long time. In order to avoid injury, do 
not remove the fan guard of the outdoor unit.

To avoid oxygen deficiency, ventilate the room 
sufficiently if equipment with burner is used together 
with the air conditioner.

Do not allow anyone to climb on the outdoor unit or 
avoid placing any object on it. Falling or tumbling may 
result in injury.

Never expose little children, plants or animals directly 
to the air flow.

Do not let children play on and around the outdoor 
unit. If they touch the unit carelessly, it may result in 
injury.

Never touch the internal parts of the controller.
Do not remove the front panel. Some parts inside are 
dangerous to touch and appliance problems may 
happen. For checking and adjusting the internal parts, 
contact your dealer.

Do not touch the heat exchanger fins. These fins are 
sharp and could result in cutting injuries.

Summary of Contents for RWEYQ10T8Y1B





























































Reviews: